Skip Navigation

Administrative Rules Home Administrative Rules

DAR File No. 32331

This filing was published in the 02/15/2009, issue, Vol. 2009, No. 4, of the Utah State Bulletin.

Natural Resources, Geological Survey

R638-2

Renewable Energy Systems Tax Credits

NOTICE OF PROPOSED RULE

DAR File No.: 32331
Filed: 01/28/2009, 01:58
Received by: NL

RULE ANALYSIS

Purpose of the rule or reason for the change:

The need for rule changes was determined through communications with taxpayers, licensed solar and geothermal contractors, state inspectors, and other industry professionals. Once the proposed rule changes were written, they were submitted to the Utah State Tax Commission, the Director of Utah Geological Survey (UGS), and the UGS Board for review and approval.

Summary of the rule or change:

The main points of the rule changes are as follows: 1) add language to include direct use geo-exchange technology as an eligible technology, and recognize the certification systems employed and certified by the Air Conditioning Heating and Refrigeration Institute (AHRI); 2) extend the solar array orientation limit of within 15 degrees of true south. Orientation restrictions have become an issue for residents that have east-and-west-facing rooftops. The State Energy Program (SEP) recommends that west-facing rooftops be included as they follow peak demand of load more closely than south-facing rooftops. In addition, east-facing roofs with a low-angle pitch (less than 30 degrees should also be allowed; 3) allow custom sized solar thermal systems, which are not found on standard industry rating lists, e.g., Solar Rating Certification Corporation (SRCC). Because these systems are large and custom made, they are not able to undergo the same certification process that standard solar hot water systems are. Each system is subject to a SEP analysis of efficiency on a case-by-case basis for custom-sized systems; and 4) increase amount allowed for reasonable cost of small wind turbine generators from $5 to $8 per watt based on available technologies and industry standards. Market trends suggest that the majority of many small wind systems are in the $6 to $8 per watt range.

State statutory or constitutional authorization for this rule:

Sections 59-7-614, 59-10-1014, and 59-10-1106

Anticipated cost or savings to:

the state budget:

The anticipated impacts to the state budget are minimal. Based on past renewable energy tax credit records, the SEP anticipates that these rule changes may result in a few more tax credits being approved yearly. The fiscal impact for these newly accepted systems is unknown, though they are anticipated to be marginal. Renewable Energy Systems Tax Credits are processed and administered by the UGS. Rule changes are not expected to substantially increase the workload of the UGS in the processing of tax credit applications.

local governments:

Local governments are not affected by the operation of the Renewable Energy Systems Tax Credit. Local governments are minimally involved, nor required to participate, in the process of the tax credit.

small businesses and persons other than businesses:

The fiscal impact for these newly accepted systems is unknown, though they are anticipated to be marginal. Some businesses may see a positive impact via increased business opportunities due to the inclusion of new technologies and more flexible design and reasonable cost criteria of technology.

Compliance costs for affected persons:

Compliance costs will not change for applicants because the basic nature of the Renewable Energy Tax Credit law remains unchanged.

Comments by the department head on the fiscal impact the rule may have on businesses:

I have reviewed the proposed rule amendments for rule R638-2 and concur with UGS's analysis that there some businesses may see a positive impact via increased business opportunities due to the inclusion of new technologies and more flexible design and reasonable cost criteria of technology. Michael R. Styler, Executive Director

The full text of this rule may be inspected, during regular business hours, at the Division of Administrative Rules, or at:

Natural Resources
Geological Survey
1594 W NORTH TEMPLE
SALT LAKE CITY UT 84116-3154

Direct questions regarding this rule to:

Jason Berry at the above address, by phone at 801-538-5413, by FAX at 801-538-4795, or by Internet E-mail at jasonberry@utah.gov

Interested persons may present their views on this rule by submitting written comments to the address above no later than 5:00 p.m. on:

03/17/2009

This rule may become effective on:

03/24/2009

Authorized by:

Michael R Styler, Executive Director

RULE TEXT

R638. Natural Resources, Geological Survey.

R638-2. Renewable Energy Systems Tax Credits.

R638-2-2. Authority.

Pursuant to Sections 59-7-614, 59-10-1014, and 59-10-1106, the UGS and the Utah Tax Commission may each make rules that are necessary to implement renewable energy tax credits for corporate and individual income tax filers. In addition, the UGS is required to certify that an energy system for which a tax credit is sought has been installed and is a viable system for saving or produc[tion]ing [of ]energy from renewable resources. For taxpayers claiming a tax credit based upon a percentage of the costs of a renewable energy system, the UGS may also set standards for residential and commercial systems that cover the safety, reliability, efficiency, leasing, and technical feasibility of the systems to ensure that they use the state's renewable and non-renewable energy resources in an appropriate and economic manner. For such percentage-of-cost credits, the UGS may also establish rules defining the reasonable costs of a system.

 

R638-2-3. Definitions.

(A) The definitions below are in addition to or serve to clarify the definitions found in Sections 59-7-614, 59-10-1014, and 59-10-1106.

(B) "Active solar thermal system" means a system of apparatus and equipment capable of intercepting and transferring incident solar thermal radiation to air or liquid by a separate apparatus to the point of storage or use. Transfer of energy to the point of storage or use must be accomplished using a mechanically powered device.

1. Active solar thermal systems include systems that:

a. Heat water for space heating, culinary water, recreational use (including swimming pools), and other industrial or commercial uses;

b. Heat a liquid, contained within a closed loop system, whose transferred heat may be used for space heating, culinary water, recreational use (including swimming pools), and other industrial or commercial uses; and

c. Heat air that is transferred to a building's conditioned space using mechanical systems such as fans or blowers either for heat or to induce air movement used for cooling.

2. Active solar thermal systems do not include systems that use heat for evaporative cooling.

(C) "Biomass system" means a system of apparatus and equipment for use in converting biomass material into fuel or electricity and transporting that energy by separate apparatus to the point of use or storage.

1. Materials that may be used to produce fuel or electricity are as follows:

a. material from a plant or tree; or

b. other organic matter that is available on a renewable basis, including:

i. slash and brush from forests and woodlands;

ii. animal waste;

iii. methane produced at landfills or as a byproduct of the treatment of wastewater residuals;

iv. aquatic plants; and

v. agricultural products.

2. A biomass system does not include:

a. A system that uses, black liquor, treated woods, or biomass from municipal solid waste other than methane produced at landfills or sewage treatment plants

b. A system that combusts biomass for the primary purpose of producing and using heat or mechanical energy.

3. In order to be considered a biomass system, a fuel or electricity producing system must use biomass as its primary source of energy.

(D) "Commercial energy system" means any active solar, passive solar, geothermal electricity, direct-use geothermal, geothermal heat-pump system, wind, hydroenergy, or biomass system used to supply energy to a commercial unit or as a commercial enterprise. In the case of systems generating electricity and involving multiple but interconnected energy generation systems, a commercial energy system includes all interconnected components that:

1. Were assembled or constructed at approximately the same time as part of a single project; and

2. Supply electricity to a common grid interconnection point.

This includes wind farms connecting to a single substation and biomass generating systems using multiple small generators. Such combinations of intertied generators are considered to be single energy systems for purposes of this rule.

(E) "Commercial tax credit" means the credits defined in Subsection 59-7-614(2)(b) and Section 59-10-1106 that provide tax credits worth 10% of the reasonable cost, up to $50,000, of a commercial energy system.

(F) "Commercial unit" means any building or structure that a business entity uses to transact its business. For purposes of the commercial investment tax credit, an agricultural water pump and a wind turbine are each considered to be single commercial units.

(G) "Direct use geothermal system" means a system of apparatus and equipment enabling the direct use of thermal energy, generally between 100 and 300 degree Fahrenheit, that is contained in the earth to meet energy needs, including heating a building, an industrial process, or aquaculture. Such systems generally make use of hot water or steam derived from wells bored through the earth's crust to reach areas of thermal energy. They may include systems that make use of groundwater or those that inject water into the earth for the purpose of deriving heat. They can also include systems that pump a heat exchanging fluid through a sealed, close loop system below the ground to extract heat for use above the earth's surface.

(H) "Eligible cost" means a cost that is reasonable as defined in this rule, that is incurred for the purchase or installation of a renewable energy system, and that may be used in computing the amount of either a commercial or residential investment tax credit.

(I) "Geothermal electricity system" means a system that uses thermal energy that flows outward from the earth as the sole source of energy for producing electricity.

(J) "Geothermal heat pump system" means a system of apparatus and equipment enabling use of the thermal properties contained in the earth well below 100 degrees Fahrenheit to help meet heating and cooling needs of a structure. For purposes of this rule, geothermal heat pump system means a system that is thermally coupled with the ground through a heat exchange medium or using mechanical heat exchange equipment and that uses a "ground-source heat pump" technology described in the American Society of Heating, Refrigerating, and Air Conditioning Engineers' (ASHRAE) Applications Handbook, Chapter 32, or the Air Conditioning Heating and Refrigeration Institute (AHRI) Certified Product Directory, Page 4-8. This can include ground source heat pumps, [and ]water source heat pumps using ground water or surface water, and direct geoexchange heat pump systems.

(K) "Grid connected" describes a system that generates electricity and is electrically connected to an electrical load that is also connected to and served by the local utility's electrical grid. To be considered grid connected, a system needs be able to serve an electrical load that is also served by the local utility.

(L) "Heat transportation system" means all fans, vents, ducts, pipes and heat exchangers designed to move heat from a collection point to either the storage or heat use area.

(M) "Investment tax credit" means a tax credit authorized in any of the Sections 59-7-614, 59-10-1014, and 59-10-1106 and that is not a production tax credit.

(N) "Loaded structure" means a part of the building that provides support to that building.

(O) "Placed in commercial service" means the earliest point in time at which a commercial energy system:

1. Produces or is capable of producing at its maximum potential output; and

2. Sells all or some portion of its energy output or uses some portion its energy output for commercial activities located at the same site.

(P) "Passive solar system" means a direct thermal system that utilizes the structure of a building and its operable components to provide for collection, storage, and distribution of heating or cooling during the appropriate times of the year by utilizing the climate resources available at the site and includes those portions and components of a building that are expressly designed and required for the collection, storage, and distribution of solar energy.

(Q) "Production tax credit" means the credits defined in Subsections 59-7-614(2)(c) and 59-10-1106(2)(b) that provides 0.35 cents per kilowatt-hour of electricity produced for wind, geothermal, or biomass systems with production capacities of 660 kilowatts or greater.

(R) "Production tax credit window" means the period during which a company is eligible to receive production tax credits for a specific commercial energy system. The window begins on the day that the system is placed in commercial service and ends 48 months after that date.

(S) "Renewable energy system" means any of the following types of systems defined in Section 57-7-614, 57-10-1014, and 57-10-1106:

1. Active solar including solar thermal and photovoltaics;

2. Biomass except for systems combusting biomass for heat;

3. Direct-use geothermal;

4. Geothermal electricity

5. Geothermal heat pump;

6. Hydroenergy;

7. Passive solar for heating or cooling;

8. Wind.

(T) "Residential investment tax credit" means the credits defined in Subsection 59-7-614(2)(a) and Section 59-10-1014 that provide tax credits worth 25% of the reasonable cost up to $2,000 of a residential energy system.

(U) "Residential unit" means any house, condominium, apartment, or similar dwelling for a person or persons, but it does not include any vehicles such as motor homes, recreational vehicles, or house boats.

(V) "Solar PV energy system" means an active solar energy system that converts light to direct current electricity through the use of semiconducting materials and that is capable of producing electricity for use in a building by the use of an inverter to produce alternating current electricity.

(W) "Thermal storage mass" means a structure within the conditioned space consisting of a material with high thermal capacitance or mass to provide heat to the unit at times of low or no heat collection.

(X) "Ton" means heating and/or air conditioning capacity equivalent to 12,000 British thermal units (Btus).

(Y) "USEP" means that Utah State Energy Program, a subdivision of the Utah Geological Survey, which is responsible for certifying tax credits specified under this rule.

(Z) "Wind energy system" means a system of apparatus and equipment capable of intercepting and converting wind energy into mechanical or electrical energy and transferring these forms of energy by a separate apparatus to the point of use, sale, or storage.

(AA) "Solar surface" is a building wall which faces no more than 30 degrees away from true south measured in a horizontal plane.

 

R638-2-4. Investment Tax Credit Certification Process.

(A) The Utah State Energy Program (USEP), a subdivision of the UGS, is responsible for certifying renewable energy systems tax credits.

(B) Applications for credits are to be made on forms developed by USEP to gather information necessary to implement this rule.

(C) USEP will evaluate each application according to the definitions and criteria established by statute and by this rule. If the information contained within an application is inadequate to determine eligibility according to this rule, USEP reserves the right to request additional information from the applicant. If an applicant is unable or unwilling to provide adequate information, USEP may deny the application and no tax credit will be certified.

(D) If, after evaluating an application, USEP finds that a renewable energy system is eligible for a residential or commercial tax credit, USEP will complete a Utah State Tax Commission Form TC-40E that will serve as the taxpayer's documentation of eligibility for a tax credit. Only USEP may issue a completed TC-40E and a tax credit may not be claimed without such documentation.

(E) Upon the completion of USEP's evaluation of an application, USEP will provide to the applicant one of the following, as appropriate:

1. A completed TC-40E allowing the full amount of tax credit requested;

2. A completed TC-40E allowing a portion of the tax credit requested accompanied by a written explanation for the denial of the full requested amount; or

3. A letter informing the applicant that the request for a tax credit has been denied and providing an explanation for the denial.

(F) If USEP denies, in whole or in part, an application for a tax credit, the taxpayer applicant may, consistent with Section [63-46b-12]63G-4-301 (Administrative Procedures Act), request that the decision be reviewed by the USEP manager. If, after review by the manager, the taxpayer desires a further appeal, he or she may request reconsideration of the decision by the director of UGS, consistent with Section [63-46b-13]63G-4-302.

(G) All applications for credits under this rule shall provide the following information:

1. The true legal name of the person or persons seeking a tax credit;

2. The tax identification number or numbers of persons seeking a tax credit;

3. The physical address, plat number, or global positioning satellite (GPS) coordinates of the property where the system is installed. Location information must be sufficient to permit USEP staff to locate the site for on-site verification of the information in the application.

4. A general description of the system, including technologies employed (e.g. wind, solar thermal), intended use, energy production capacity, cost, date of completed installation, and other information specified in this rule.

(H). Applications for residential and commercial tax credits must provide, either within an application form or provided as supporting documentation, each of the following:

1. Detailed diagrams of the system installed such that USEP staff, evaluating each proposal, can distinguish all major system components, how the system operates, and which components are eligible costs for computing the tax credit.

2. Photographs or copies of photographs that show major system components, how and where the system is installed, electrical interconnections with the power grid or other components of the electrical system at the taxpayer's home or business, and any other components of the renewable energy system that demonstrate that individual components are eligible costs under this rule. Photographs or copies of photographs should also demonstrate that a system is constructed in a safe and reliable manner.

3. Clear documentation of costs incurred for all components of the renewable energy system. Original or reproduced copies of all receipts or invoices should be provided and all invoices from contractors or equipment dealers must show that the invoiced amounts were paid by the taxpayer; otherwise, copies of canceled checks should be provided. Documentation should also include an itemized listing of all components of an installed system, including manufacturer and model numbers for major equipment components, the costs of all major components, and costs for labor, installation, and/or design. The sum of documentation provided should be sufficient to allow UGS to identify all eligible and ineligible costs and to determine whether such costs are reasonable. Applications that do not include a clear itemization of system costs will not be considered.

 

R638-2-6. Investment Tax Credit, Eligible Costs for Commercial and Residential Systems, Active Solar Thermal.

(A) All eligible costs for active solar thermal energy systems must conform with Section R638-2-5, above. Active solar thermal energy systems must also meet the requirements in this Section.

(B) For purposes of determining eligible costs, an active solar thermal system ends at the interface between it and the conventional heating system. Eligible costs for a solar thermal system are limited to components that would not normally be associated with a conventional hot water heating system. Eligible equipment costs include:

1. Solar collectors that transfer solar heat to water, a heat transfer fluid, or air;

2. Thermal storage devices such as tanks or heat sinks;

3. Ductwork, piping, fans, pumps and controls that move heat directly from solar collectors to storage or to the interface between the active solar thermal system and a building's conventional heating and cooling systems.

(C) Hot water storage tanks that have dual heat exchange capabilities allowing for the heating of water by both the active solar thermal system and by a nonrenewable energy source such as natural gas or electricity are eligible for tax credits. However only one half of the costs of purchasing and installing such tanks are eligible costs for the purposes of calculating a commercial or residential tax credit.

(D) In order to be eligible for residential or commercial tax credits, a solar collector that heats water must be certified and rated by the Solar Rating Certification Corporation (SRCC) according to SRCC Standard 100, "Test Methods and Minimum Standards for Certifying Solar Collectors."

(E) In order to be eligible for residential or commercial tax credits, an active solar thermal system installed after December 31, 2008 and that heats water must be certified and rated by the Solar Rating Certification Corporation (SRCC) according to SRCC Document OG-300, "Operating Guidelines and Minimum Standards for Certifying Solar Water Heating Systems." The applicant can demonstrate to USEP that the solar thermal system meets standards that are equivalent to those of the SRCC Document OG-300 by providing:

1. Detailed engineering design and performance data that show system performance, or

2. Certification from other recognized National or European solar thermal testing labs.

(F) In order to be eligible for a residential or commercial tax credit, the taxpayer applicant must demonstrate that a solar thermal energy system has been sited and installed appropriately in order to realize the maximum feasible energy efficiency for a given location. Specifically, the system should conform with the following:

1. Solar collectors shall be free of shade (vent pipes, trees, chimneys, etc.) and positioned accordingly so as to optimize the average annual solar ration values (kWh/M2/day). Guidance for siting may be found at the National Renewable Energy Laboratory's (NREL) National Solar Radiation Database, which can be found at:

http://rredc.nrel.gov/solar/pubs/redbook/PDFs/UT.PDF;

2. Fixed, non-glazed collectors shall be:[ oriented within 15 degrees of true south, except that non-glazed collectors used for heating pool water shall be:]

a. Oriented within 45 degrees of true south if the fixed pitch is greater than 30 degrees from horizontal, or

b. Oriented within 90 degrees of true south if the fixed pitch is 30 degrees or less from horizontal.

3. Fixed, glazed collectors shall be:

a. 165 degrees and 225 degrees if the fixed pitch is greater than 30 degrees from horizontal, or

b. 165 degrees and 270 degrees if the fixed pitch is 30 degrees or less from horizontal.

(G) In order to be eligible for a residential or commercial tax credit, all solar hot water thermal systems shall be installed by one of the following licensed contractors:

1. A Utah licensed plumbing contractor (S210 license);

2. A Utah licensed solar hot water contractor (S215 license); or

3. A licensed contractor who has obtained written approval by the Utah Department of Occupational Licensing for the installation of solar hot water systems.

(H) In order to be eligible for a residential or commercial tax credit, an active solar thermal system must be certified for safety by one of the following:

1. A Utah licensed plumbing contractor (S210 license);

2. A Utah licensed solar hot water contractor (S215 license); or

3. A county or municipal building inspector licensed by the State of Utah.

Proof of this certification may be required on the tax credit application.

(I) For purposes of computing eligible costs for residential and commercial tax credits, the reasonable cost of a flat panel active solar thermal system is considered to be no higher than $0.15 per Btu/day of heat output for all eligible costs listed above and in Section R638-2-5 and prior to any cash rebates or incentives that the taxpayer may receive from a third party (such as a utility). The determination of heat output shall be based upon the ratings of the Solar Rating Certification Corporation (SRCC) "Summary of SRCC Certified Solar Collectors and Water Heating System Ratings" that is found at:

http://www.solar-rating.org/ratings/ratings.htm.

1. For a residential tax credit application with total pre-rebate eligible costs exceeding $0.15 per Btu/day of capacity, the amount of the tax credit shall be calculated as follows:

Tax credit granted = (($0.15 x rated output capacity in Btu/day) - rebates) x 0.25

2. For a commercial tax credit application with total eligible costs exceeding $0.15 per Btu/day, the amount of the tax credit shall be calculated as 10% of costs calculated as follows:

Tax credit granted = (($0.15 x rated output capacity in Btu/day) - rebates) x 0.10

3. If the cost of a flat panel active solar thermal system exceeds $0.15 per Btu/day of capacity due to unusual and/or unavoidable circumstances (such as a multi-story structure retrofit or difficult pipe chase and interconnection conditions) the taxpayer applicant may request that the reasonable cost limitation above be waived by USEP. In order to do so, the applicant must provide written documentation and explanation from the designer or installer of the system as to why the final system cost exceeded this limit. Granting of such a waiver will be at the discretion of USEP and UGS after investigation as to the validity of the waiver claim.

(J) For purposes of computing eligible costs for residential and commercial tax credits, the reasonable cost of an evacuated tube active solar thermal system is considered to be no higher than $0.27 per Btu/day of heat output for all eligible costs listed above and in Section R638-2-5 and prior to any cash rebates or incentives that the taxpayer may receive from a third party (such as a utility). The determination of heat output shall be based upon the ratings of the Solar Rating Certification Corporation (SRCC) "Summary of SRCC Certified Solar Collectors and Water Heating System Ratings" that is found at:

http://www.solar-rating.org/ratings/ratings.htm.

1. For a residential tax credit application with total pre-rebate eligible costs exceeding $0.27 per Btu/day of capacity, the amount of the tax credit shall be calculated as follows:

Tax credit granted = (($0.27 x rated output capacity in Btu/day) - rebates) x 0.25

2. For a commercial tax credit application with total eligible costs exceeding $0.27 per Btu/day, the amount of the tax credit shall be calculated as 10% of costs calculated as follows:

Tax credit granted = (($0.27 x rated output capacity in Btu/day) - rebates) x 0.10

3. If the cost of a flat panel solar thermal system exceeds $0.27 per Btu/day of capacity due to unusual and/or unavoidable circumstances (such as multi-story structure retrofit or difficult pipe chase and interconnection conditions) the taxpayer applicant may request that the reasonable cost limitation above be waived by USEP. In order to do so, the applicant must provide written documentation and explanation from the designer or installer of the system as to why the final system cost exceeded this limit. Granting of such a waiver will be at the discretion of USEP and UGS after investigation as to the validity of the waiver claim.

 

R638-2-7. Investment Tax Credit, Eligible Costs for Commercial and Residential Systems, Solar PV (Photovoltaic).

(A ) All eligible costs for solar PV energy systems must conform with Section R638-2-5, above. Solar PV energy systems must also meet the requirements in this Section.

(B) The costs of the following solar PV energy system components are eligible for residential or commercial tax credits:

1. Solar PV module(s);

2. Inverter;

3. Motors and other elements of a tracking array;

4. Mounting hardware;

5. Wiring and disconnects from modules to the inverter and from the inverter to the point of interconnection with the AC panel;

6. Lightning arrestors.

(C) The costs of additional components of solar PV energy systems are eligible for residential or commercial tax credits if the solar PV system is not grid connected and it provides electricity to a building or structure that is more than one quarter mile from a power distribution line operated by a retail electric utility provider. If these conditions are met, the following components are also eligible:

1. Batteries;

2. Battery wiring;

3. Charge controllers; and

4. Battery temperature sensors.

(D) The costs of solar PV modules are eligible for Utah tax credits only if they are:

1. Listed as eligible modules under the California Solar Initiative Program. A list of eligible modules may be found at the following site:

[http://www.consumerenergycenter.org/cgi-bin/eligible_pvmodules.cgi]http://www.gosolarcalifornia.org/equipment/index.html; or

2. The applicant can demonstrate to USEP that the modules meet standards that are equivalent to those of the California Solar Initiative Program as of calendar year 2007.

(E) For grid connected solar PV systems, the cost of inverters are eligible for Utah tax credits only if:

1. They are also listed as eligible inverters under the California Solar Initiative Program. A list of eligible inverters may be found at the following site:

[http://www.consumerenergycenter.org/cgi-bin/eligible_inverters.cgi]http://www.gosolarcalifornia.org/equipment/index.html; or

2. The applicant can demonstrate to USEP that the inverter meets standards that are equivalent to those of the California Solar Initiative Program as of calendar year 2007.

(F) Solar PV modules must be must be certified for safety by a Nationally Recognized Testing Laboratory and be warranted by the manufacturer to produce at least 80% of rated output after twenty years of operation.

(G) Inverters and charge controllers must be certified for safety by a Nationally Recognized Testing Laboratory and be warranted by the manufacturer against failure due to materials and workmanship for at least five years.

(F) All solar PV energy systems must be designed and installed consistent with the National Electric Code Article 690.

(G) Grid connected systems must meet all interconnection standards of the local electrical utility and must include with an application for a residential or commercial tax credit a copy of an interconnection or net metering agreement with the local electrical utility.

(H) The costs of system performance monitoring hardware and software are not eligible for residential or commercial tax credits. Grid connected backup power and monitoring systems such as Grid Point back-up power systems are not eligible for the tax credit with the exception that the inverter within such systems will be considered to carry a cost of $2,500 for the purpose of calculating the tax credit.

(I) In order to be eligible for a residential or commercial tax credit, the taxpayer applicant must demonstrate that a solar PV energy system has been sited and installed appropriately. Specifically, the system should be:

1. Located such that the solar modules are completely free of shade from trees and other plants, buildings, chimneys, vent pipes, utility poles, and other objects that would reduce system output for at least two-thirds of the daylight hours at the site;

2. Positioned so as to optimize the average annual solar radiation values (kWh/M2/day). Guidance for siting may be found at the [the ]National Renewable Energy Laboratory's (NREL) National Solar Radiation Database (found at:

http://rredc.nrel.gov/solar/pubs/redbook/PDFs/UT.PDF);

3. Positioned such that the fixed [modules and/or]solar array[s] azimuth shall be[are] oriented within:[ 15 degrees of true south.]

a. 165 degrees and 225 degrees if the fixed pitch is greater than 30 degrees from horizontal, or

b. 165 degrees and 270 degrees if the fixed pitch is 30 degrees or less from horizontal.

(J) In order to be eligible for a residential or commercial tax credit, a solar PV energy system must be certified for safety by one of the following:

1. A Utah licensed electrical contractor (S200);

2. A Utah licensed solar photovoltaic contractor (S202);

3. A licensed contractor who has obtained written approval by the Utah Department of Occupational Licensing for the installation of solar PV systems; or

4. A county or municipal building inspector licensed by the State of Utah. Proof of this certification may be required on the tax credit application.

(K) For purposes of computing eligible costs for residential and commercial tax credits, the reasonable cost of a solar PV energy system that is grid connected or that provides electricity to a building or structure that is one quarter mile or less from a power distribution line operated by a retail electric utility provider is considered to be no higher than $10 per watt of rated output capacity for all eligible costs listed above and in Section R638-2-5 and prior to any cash rebates or incentives that the taxpayer may receive from a third party (such as a utility).

1. For a residential tax credit application with total pre-rebate eligible costs exceeding $10 per watt of capacity, the amount of the tax credit shall be calculated as follows:

Tax credit granted = (($10 x rated output capacity in watts) - rebates) x 0.25

2. For a commercial tax credit application with total eligible costs exceeding $10 per watt, the amount of the tax credit shall be calculated as 10% of costs calculated as follows:

Tax credit granted = (($10 x rated output capacity in watts) - rebates) x 0.10

(L) For purposes of computing eligible costs for residential and commercial tax credits, the reasonable cost of solar PV energy system that is not grid connected and that provides electricity to a building or structure that is more than one quarter mile from a power distribution line operated by a retail electric utility provider is considered to be no higher than $13 per watt of rated output capacity for all eligible costs listed above and in Section R638-2-5 and prior to any cash rebates or incentives that the taxpayer may receive from a third party (such as a utility).

1. For a residential tax credit application with total pre-rebate eligible costs exceeding $13 per watt of capacity, the amount of the tax credit shall be calculated as follows:

Tax credit granted = (($13 x rated output capacity in watts) - rebates) x 0.25

2. For a commercial tax credit application with total eligible costs exceeding $13 per watt, the amount of the tax credit shall be calculated as 10% of costs calculated as follows:

Tax credit granted = (($13 x rated output capacity in watts) - rebates) x 0.10

 

R638-2-9. Investment Tax Credit, Eligible Costs for Commercial and Residential Systems, Wind.

(A) All eligible costs for wind energy systems must conform with Section R638-2-5, above. Wind energy systems must also meet the requirements in this Section.

(B) Wind systems of 50 kilowatts generating capacity or less must include a wind turbine that is either:

1. Listed as eligible under the California Emerging Renewables Program in order to be eligible for a Utah commercial or residential tax credit. This list may be found at the following site: http://www.consumerenergycenter.org/cgi-bin/eligible_smallwind.cgi; or

2. The applicant can demonstrate to USEP that the turbine meets standards that are equivalent to those of the California Emerging Renewables Program as of calendar year 2007.

(C) Inverters and charge controllers must by certified for safety by a Nationally Recognized Testing Laboratory as meeting Underwriters Laboratory Standard 1741.

(D) All wind energy systems must be designed and installed consistent with the National Electric Code. Grid connected systems must also meet all interconnection standards of the local electrical utility. Applications for residential or commercial tax credits for grid[]-connected systems must include a copy of an interconnection or net metering agreement with the local electrical utility.

(E) In order to be eligible for a residential or commercial tax credit, the taxpayer applicant must demonstrate that a wind energy system has been sited and installed appropriately. Specifically, the system should be:

1. Installed such that the central tower or pole upon which the turbine is mounted is located a distance at least equal to one and one-half times the height of the tower or pole from any:

a. Buildings;

b. Utility poles or overhead utility lines;

c. Fences, roads, or other structures outside of the boundaries of the taxpayer's property.

2. Installed such that wind flowing to the system is not obstructed or airflow diminished or turbulence created by nearby:

a. Trees or other vegetation;

b. Buildings and other structures;

c. Hills, cliffs, or other topographical obstructions.

The photographs included with a wind energy system should include views of the system from all angles such that SEP can verify appropriate siting. SEP also reserves the right to conduct a site visit to verify appropriate siting.

(F). Wind turbines mounted on buildings are not eligible unless it can be demonstrated by a professional engineer that the building's soundness and structural integrity are not compromised by the wind energy system and that the attachments of the system to the building are sufficient to withstand the most extreme local weather conditions.

(G) Wind energy systems must include lightning protection to be eligible for residential or commercial tax credits.

(H) Wind turbines must be covered by a manufacturer's warranty that guarantees against defects in design, material, and workmanship for at least five years after installation under normal use in a wind energy system.

(I) In order to be eligible for a residential or commercial tax credit, a wind energy system must comply with all local building or zoning ordinances. Copies of any required permits should be included with the tax credit application.

(J) In order to be eligible for a residential or commercial tax credit, a wind energy system must be certified for electrical safety by either:

1. A professional electrician licensed by the State of Utah;

2. A county or municipal building inspector licensed by the State of Utah.

Proof of this certification may be required with the tax credit application.

(K) For purposes of computing eligible costs for residential and commercial tax credits, the reasonable cost of a wind energy system is considered to be no higher than $[5]8 per watt of rated output capacity for all eligible costs listed above and in Section R638-2-5 and prior to any cash rebates or incentives that the taxpayer may receive from a third party (such as a utility).

1. For a residential tax credit application with total pre-rebate eligible costs exceeding $5 per watt of capacity, the amount of the tax credit shall be calculated as follows:

Tax credit granted = (($[5]8 x rated output capacity in watts) - rebates) x 0.25

2. For a commercial tax credit application with total eligible costs exceeding $[5]8 per watt, the amount of the tax credit shall be calculated as 10% of costs calculated as follows:

Tax credit granted = (($[5]8 x rated output capacity in watts) - rebates) x 0.10

 

R638-2-10. Investment Tax Credit, Eligible Costs for Commercial and Residential Systems, Geothermal Heat Pumps.

(A) All eligible costs for geothermal heat pump systems must conform with Section R638-2-5, above. Geothermal heat pump systems must also meet the requirements in this Section.

(B) In order to be eligible for residential or commercial tax credits, a geothermal heat pump system employed to heat and/or cool a building must derive at least 75% of the heating and cooling from the ground. Systems that provide more than an insignificant amount of energy to the building using combustion, cooling towers, air-source heat pumps, or any other mechanism not involving thermal ground coupling are not eligible.

(C) In order to be eligible for residential or commercial tax credits, a geothermal heat pump system must conform with the design and practice guidelines described in the American Society of Heating, Refrigerating, and Air Conditioning Engineers' (ASHRAE) Applications Handbook, Chapter 32, or Air Conditioning Heating and Refrigeration Institute (AHRI) Certified Product Directory, Page 4-8.

(D) In order to be eligible for residential or commercial tax credits, a geothermal heat pump system must have been designed by either:

1. A professional engineer licensed in Utah;

2. A person designated as a "Certified GeoExchange Designer" by the Association of Energy Engineers; or

3. A person designated as a "Certified Energy Manager" by the Association of Energy Engineers; or

4. For geothermal heat pump systems installed in a residential unit only, a person designated as an "Accredited Installer" by the International Ground Source Heat Pump Association (IGSHPA).

5. For direct geoexchange systems, a person designated as a certified designer by an AHRI accredited direct geoexchange systems manufacturer.

Proof of designer qualification may be required on the tax credit application.

(E) In order to be eligible for residential or commercial tax credits, a geothermal heat pump system must have been installed by a plumber licensed (S210) or HVAC contractor (S350) in the State of Utah or by an installer certified by the International Ground Source Heat Pump Association (IGSHPA). Proof of installer qualification may be required on the tax credit application.

(F) In the case of a system using a vertical bore (either ground source or water source), drilling must be performed by a water well driller licensed by the Utah Division of Water Rights. Wells drilled for a vertical bore must also obtain a provisional well approval from the Utah Division of Water Rights, Department of Natural Resources. Proof of driller qualifications and well approval may be required on the tax credit application.

(G) Costs incurred for the drilling of wells or excavating trenches are eligible if actually used within the final system for the exchange of heat with the ground. The cost of exploratory wells or trenches that are not used within the final system are not eligible.

(H) Design costs for a geothermal heat pump system are eligible but only for the components of the system that would not normally be associated with a conventional heating and air conditioning system. Tax credit applications should separate design costs for the geothermal and conventional components of the system.

(I) For closed loop systems (both ground source and water source), the heat exchanging pipe loop shall be warranted by the installer against leakage or breakage for not less than three years from the date of installation.

(J) For purposes of computing eligible costs for residential and commercial tax credits, the reasonable cost of a geothermal heat pump system is considered to be no higher than $4,000 per ton of output capacity for all eligible costs listed above and in Section R638-2-5 and prior to any cash rebates or incentives that the taxpayer may receive from a third party (such as a utility).

1. For a residential tax credit application with total pre-rebate eligible costs exceeding $4,000 per ton of capacity, the amount of the tax credit shall be calculated as follows:

Tax credit granted = (($4,000 x rated output capacity in tons) - rebates) x 0.25

2. For a commercial tax credit application with total eligible costs exceeding $4,000 per ton, the amount of the tax credit shall be calculated as 10% of costs calculated as follows:

Tax credit granted = (($4,000 x rated output capacity in tons) - rebates) x 0.10

3. If the cost of a geothermal heat pump system exceeds $4,000 per ton of capacity due to unusual and/or unavoidable circumstances (such as poor soil or drilling conditions) the taxpayer applicant may request that the reasonable cost limitation above be waived by USEP. In order to do so, the applicant must provide written documentation and explanation from the designer or installer of the system as to why the final system cost exceeded this limit. Granting of such a waiver will be at the discretion of USEP and UGS after investigation as to the validity of the waiver claim.

 

R638-2-15. Certification of Production Tax Credit Eligibility.

(A) Businesses seeking to claim production tax credits must first apply to USEP for certification that a commercial energy system has been installed, is a viable energy production system, and meets all other relevant requirements of Sections 59-7-614 and 59-10-1106. Such certification shall be sought within the first six months of the system being placed into commercial service.

(B) Eligibility for production tax credits is limited to commercial energy systems that are also any of the following:

1. Biomass systems;

2. Wind energy systems; or

3. Geothermal electricity systems.

In addition, the name plate capacity of any system seeking production tax credits must be 660 kilowatts or greater. Electricity produced by the system must either be used by the business seeking a production tax credit or sold in order to be eligible for credits.

(C) Businesses may request certification by providing the following to USEP:

1. A written request for certification of a commercial energy system for eligibility to receive a production tax credit;

2. Information about the company seeking certification, including legal name, type of legal entity, address, telephone number, and the name and telephone number of a contact person regarding the request;

3. A description of the commercial energy system including the type of facility, total nameplate capacity, the methods to be used to produce fuel or electricity, and a list of major fuel or electricity producing components. Systems generating electricity should also provide the number, manufacturer, and model number of generating turbines to be used;

4. Information on the location of the commercial energy system sufficient to permit site inspection by USEP staff. For wind farms this should include a map of the turbine layout. For geothermal systems this should include a map showing production and injection wells along with the location of the generating turbine or turbines;

5. Photographs of key and/or representative components of the commercial energy system;

6. Projected annual electricity production in kilowatt hours for the commercial energy system once it has entered commercial service;

7. The date on which the commercial energy system entered or is expected to enter commercial service.

(D) A business requesting certification for production tax credits must also include with its request information on ownership of the commercial energy system. If the business seeking tax credit certification leases the commercial energy system, it must provide with its request evidence that the lessor of the system has irrevocably elected not to claim production tax credits for the system.

(E) If a business plans to claim production tax credits for electricity that is used and not sold, it must install a separate metering system to measure the electricity production of the commercial energy system. Such metering should be unidirectional, tamperproof, and should measure only the electricity production attributable to the commercial energy system. The meter must also measure net electricity from the system (i.e. gross electricity from the generator minus any electricity used to operate the system itself).

(F) Upon receipt of a request for certification, USEP staff will assess whether the commercial energy system applying for production tax credit certification is a viable system and whether the system has been completely installed. USEP may request that a field inspection take place to verify information in the certification request and to ensure that the system conforms with the requirements of Section 59-7-614 and with this rule.

(G) USEP will respond to a request for certification of eligibility for production tax credits within sixty days of receipt. However, if incomplete information is received or permission for field inspection has not been granted after sixty days, USEP will have an additional 30 days after receipt of complete information and/or field inspection to respond positively or negatively to a certification request.

(H) Consistent with Title 63G, Chapter 4[6b] (Administrative Procedures Act), upon its decision to grant or deny a certification request, USEP will inform the requesting company in writing of its decision. A copy of the written decision will also be provided to the Utah State Tax Commission in order to document the company's eligibility to claim production tax credits on future tax returns.

 

R638-2-16. Granting of Production Tax Credits.

(A) In order for a company to be granted production tax credits on a return filed under Chapter 59, Chapter 7, Corporate Franchise and Income Taxes, or Chapter 10, Individual Income Tax Act, USEP must validate the amount of tax credits the company may claim for each commercial energy system. In order to claims to be validated, the company must submit to USEP information regarding the following:

1. The date that the commercial energy system first entered commercial service;

2. The beginning and ending dates of the company's tax year;

3. The number of kilowatt hours produced by the system that were sold or used during the company's tax year and that were also used or sold within the system's production tax credit window.

All such information will be provided on a standard claim form created by USEP.

(B) For purposes of validating the number of kilowatt hours sold, the company should also submit to USEP invoices or other information that documents that number of kilowatt hours of electricity sold.

(C) For purposes of validating the number of kilowatt hours produced and used, the company should submit monthly readings from the meter used to measure the net output of the commercial energy system. USEP will retain the right to site inspect the system and meter to validate that the readings provided are true and accurate.

(D) Once it has received a production tax credit claim from a company, USEP will make a determination as to:

1. Whether the information provided conforms with this rule and is complete;

2. Whether the number of kilowatt hours claimed appears to be feasible and accurate;

3. The number of kilowatts deemed to be valid;

4. The amount of tax credit that the company may claim on its corporate income tax return. This amount will equal 0.35 cents per each validated kilowatt hour of electricity used or sold during the company's tax year and within the systems production tax credit window.

(E) A company claiming a production tax credit must submit the information specified above to USEP on or before the date the tax return on which the credit is claimed is required to be filed with the State Tax Commission. Once USEP has received complete information necessary to validate a production tax credit claim, it will provide to the company a completed validation form (to be created by either USEP or the Utah State Tax Commission) within thirty days. The form will specify the validated number of kilowatt hours that are eligible for credit and the amount (in dollars) of production tax credits that the company may claim for the commercial energy system for that tax year.

(F) If USEP denies, in whole or in part, an application for a tax credit, the taxpayer applicant may, consistent with Section [63-46b-12]63G-4-301 (Administrative Procedures Act), request that the decision be reviewed by the USEP manager. If, after review by the manager, the taxpayer desires a further appeal, he or she may request reconsideration of the decision by the director of UGS, consistent with Section [63-46b-13]63G-4-302.

(G) Information submitted by an applicant under this section for validating a production tax credit claim will be classified as protected information under UC [63-2-304 (1)]63G-2-305)(1) and/or UC [63-2-304 (2)]63G-2-305(2) when the applicant provides USEP with a written claim of confidentiality and a concise statement supporting the claim, consistent with UC [63-2-308 (1)(a)(i)]63G-2-309(1)(a)(i). USEP shall provide the opportunity to make such a claim on the standard form referenced in subsection (A) above.

 

KEY: energy, renewable, tax credits, solar

Date of Enactment or Last Substantive Amendment: [March 10, 2008]2009

Authorizing, and Implemented or Interpreted Law: 59-7-614; 59-10-1014; 59-10-1106

 

 

ADDITIONAL INFORMATION

Text to be deleted is struck through and surrounded by brackets (e.g., [example]). Text to be added is underlined (e.g., example). Older browsers may not depict some or any of these attributes on the screen or when the document is printed.

For questions regarding the content or application of this rule, please contact Jason Berry at the above address, by phone at 801-538-5413, by FAX at 801-538-4795, or by Internet E-mail at jasonberry@utah.gov

For questions about the rulemaking process, please contact the Division of Administrative Rules (801-538-3764). Please Note: The Division of Administrative Rules is NOT able to answer questions about the content or application of these administrative rules.

Last modified:  02/13/2009 12:44 PM