File No. 36687
This rule was published in the September 15, 2012, issue (Vol. 2012, No. 18) of the Utah State Bulletin.
Commerce, Occupational and Professional Licensing
Rule R156-55a
Utah Construction Trades Licensing Act Rule
Notice of Proposed Rule
(Amendment)
DAR File No.: 36687
Filed: 08/23/2012 10:46:52 AM
RULE ANALYSIS
Purpose of the rule or reason for the change:
The Division and Construction Services Commission are proposing amendments to this rule to clarify the work that is allowed under the S350 HVAC (Heating, Ventilation and Air Conditioning) contractor and S211 boiler installation contractor and the experience required to obtain the S211 boiler installation classification. Proposed amendments also update statutory citations as needed. Proposed amendments also add the R200 Factory Built Housing Contractor classification to the listing of classifications requiring a trade examination.
Summary of the rule or change:
In Section R156-55a-301, updated statutory citations in B200 classification. S211 Boiler Installation Contractor and S350 HVAC Contractor - amendments in these two sections clarify that work on residential boilers and water heaters is not included in the S211 or S350 classifications. The S211 classification was originally established for work on commercial boiler systems. Recent development of residential type boilers required clarification that this type of work is not allowed in these classification. Residential boilers and water heaters should be installed by a licensed plumbing contractor under the S210 classification. In Section R156-55a-302a, the proposed amendment adds the R200 Factory Built Housing contractor classification to the list of classifications requiring a trade examination. When this list of classifications requiring trade examinations was first included in the rule on 06/24/2008, the R200 classification was included in the proposed list but was inadvertently left off the list that was ultimately placed in the rule. This change corrects that error. In Section R156-55a-302b, the proposed amendments clarify that the experience required for the S211 classification shall be installation of commercial type boilers. Proposed amendments also change the experience requirement from two years to four years for this classification due to the complicated nature of commercial boilers.
State statutory or constitutional authorization for this rule:
- Subsection 58-1-106(1)(a)
- Subsection 58-1-202(1)(a)
- Section 58-55-101
- Subsection 58-55-308(1)(a)
- Subsection 58-55-102(39)(a)
Anticipated cost or savings to:
the state budget:
The Division will incur minimal costs of approximately $50 to print and distribute the rule once the proposed amendments are made effective. Any costs incurred will be absorbed in the Division's current budget.
local governments:
The proposed amendments only apply to licensed contractors in the affected classifications and applicants for licensure in those classifications. As a result, the proposed amendments do not apply to local governments.
small businesses:
The proposed amendments only apply to licensed contractors in the affected classifications which may qualify as a small business and applicants for licensure in those classifications. The change in the experience requirement for the S211classification will require contractors who apply for the S211 classification to have four years experience rather than two years or alternatively hire a licensed plumber at least part time. The number of contractors affected or the cost to meet this requirement is impossible to estimate. The change to clarify the S211 classification is for commercial boilers would not result in any significant impact from contractors using the S211 classification as originally intended. However, if a contractor has been using this classification to perform work on residential boilers or water heaters, such a contractor would, after the rule change, be required to obtain the S200 classification in order to continue to do that type of work. Obtaining the S200 classification would require submitting an application and requires employing a qualified plumber, working at least part time. The application fee to add the classification is $200. In addition, if the qualified plumber had not previously taken the Utah Laws and Rules examination, the plumber would need to take and pass that examination. The cost of the examination is $72. It is impossible to estimate how many contractors would be affected by the rule change and the total cost that they may incur in addition to the above costs in order to obtain the additional classification.
persons other than small businesses, businesses, or local governmental entities:
The proposed amendments only apply to licensed contractors in the affected classifications and applicants for licensure in those classifications. The change in the experience requirement for the S211classification will require contractors who apply for the S211 classification to have four years experience rather than two years or alternatively hire a licensed plumber at least part time. The number of contractors affected or the cost to meet this requirement is impossible to estimate. The change to clarify the S211 classification is for commercial boilers would not result in any significant impact from contractors using the S211 classification as originally intended. However, if a contractor has been using this classification to perform work on residential boilers or water heaters, such a contractor would after the rule change, be required to obtain the S200 classification in order to continue to do that type of work. Obtaining the S200 classification would require submitting an application and requires employing a qualified plumber, working at least part time. The application fee to add the classification is $200. In addition, if the qualified plumber had not previously taken the Utah Laws and Rules examination, the plumber would need to take and pass that examination. The cost of the examination is $72. It is impossible to estimate how many contractors would be affected by the rule change and the total cost that they may incur in addition to the above costs in order to obtain the additional classification.
Compliance costs for affected persons:
The proposed amendments only apply to licensed contractors in the affected classifications and applicants for licensure in those classifications. The change in the experience requirement for the S211classification will require contractors who apply for the S211 classification to have four years experience rather than two years or alternatively hire a licensed plumber at least part time. The number of contractors affected or the cost to meet this requirement is impossible to estimate. The change to clarify the S211 classification is for commercial boilers would not result in any significant impact from contractors using the S211 classification as originally intended. However, if a contractor has been using this classification to perform work on residential boilers or water heaters, such a contractor would after the rule change, be required to obtain the S200 classification in order to continue to do that type of work. Obtaining the S200 classification would require submitting an application and requires employing a qualified plumber, working at least part time. The application fee to add the classification is $200. In addition, if the qualified plumber had not previously taken the Utah Laws and Rules examination, the plumber would need to take and pass that examination. The cost of the examination is $72. It is impossible to estimate how many contractors would be affected by the rule change and the total cost that they may incur in addition to the above costs in order to obtain the additional classification.
Comments by the department head on the fiscal impact the rule may have on businesses:
As described in the rule summary, there will be a fiscal impact to some licensees as a result of this rule filing which requires additional experience and examination for certain licensees, as well as the clarification that the S211 classification does not include work on residential boilers. The cost to licensees is difficult to estimate as it is not clear how many licensees are affected by the rule change.
Francine A. Giani, Executive Director
The full text of this rule may be inspected, during regular business hours, at the Division of Administrative Rules, or at:
CommerceOccupational and Professional Licensing
HEBER M WELLS BLDG
160 E 300 S
SALT LAKE CITY, UT 84111-2316
Direct questions regarding this rule to:
- Dan Jones at the above address, by phone at 801-530-6720, by FAX at 801-530-6511, or by Internet E-mail at [email protected]
Interested persons may present their views on this rule by submitting written comments to the address above no later than 5:00 p.m. on:
10/15/2012
Interested persons may attend a public hearing regarding this rule:
- 09/26/2012 09:00 AM, Heber Wells Bldg, 160 E 300 S, Conference Room 474, Salt Lake City, UT
This rule may become effective on:
10/22/2012
Authorized by:
Mark Steinagel, Director
RULE TEXT
R156. Commerce, Occupational and Professional Licensing.
R156-55a. Utah Construction Trades Licensing Act Rule.
R156-55a-301. License Classifications - Scope of Practice.
(1) In accordance with Subsection 58-55-301(2), the classifications of licensure are listed and described in this section. The construction trades or specialty contractor classifications listed are those determined to significantly impact the public health, safety, and welfare. A person who is engaged in work which is included in the items listed in Subsections R156-55a-301(4) and (5) is exempt from licensure in accordance with Subsection 58-55-305(1)(i).
(2) Licenses shall be issued in the following primary classifications and subclassifications:
E100 - General Engineering Contractor. A General Engineering contractor is a contractor licensed to perform work as defined in Subsection 58-55-102(22).
B100 - General Building Contractor. A General Building contractor is a contractor licensed to perform work as defined in Subsection 58-55-102(21) and pursuant to Subsection 58-55-102(21)(b) is clarified as follows:
(a) The General Building Contractor scope of practice does not include activities described in this Subsection under specialty classification S202 - Solar Photovoltaic Contractor unless the work is performed under the immediate supervision of an employee who holds a current certificate issued by the North American Board of Certified Energy Practitioners.
(b) The General Building Contractor scope of practice does not include activities described in this Subsection under specialty classification S354-Radon Mitigation Contractor unless the work is performed under the immediate supervision of an employee who holds a current certificate issued by the National Radon Safety Board (NRSB) or the National Radon Proficiency Program (NEHA-NRPP).
B200 - Modular Unit Installation
Contractor. Set up or installation of modular units as defined in
Subsection [58-56-3(15)]15A-1-302(8) and constructed in accordance with Section [58-56-13]15A-1-304. The scope of the work permitted under this
classification includes construction of the permanent or temporary
foundations, placement of the modular unit on a permanent or
temporary foundation, securing the units together if required and
securing the modular units to the foundations. Work excluded from
this classification includes installation of factory built housing
and connection of required utilities.
R100 - Residential and Small Commercial Contractor. A Residential and Small Commercial contractor is a contractor licensed to perform work as defined in Subsection 58-55-102(32) and pursuant to Subsection 58-55-102(32) is clarified as follows:
(a) The Residential and Small Commercial Contractor scope of practice does not include activities described in this Subsection under specialty classification S202 - Solar Photovoltaic Contractor unless the work is performed under the immediate supervision of an employee who holds a current certificate issued by the North American Board of Certified Energy Practitioners.
(b) The Residential and Small Commercial Contractor scope of practice does not include activities described in this Subsection under specialty classification S354-Radon Mitigation Contractor unless the work is performed under the immediate supervision of an employee who holds a current certificate issued by the National Radon Safety Board (NRSB) or the National Radon Proficiency Program (NEHA-NRPP).
R101 - Residential and Small Commercial Non Structural Remodeling and Repair. Remodeling and repair to any existing structure built for support, shelter and enclosure of persons, animals, chattels or movable property of any kind with the restriction that no change is made to the bearing portions of the existing structure, including footings, foundation and weight bearing walls; and the entire project is less than $50,000 in total cost.
R200 - Factory Built Housing Contractor. Disconnection, setup, installation or removal of manufactured housing on a temporary or permanent basis. The scope of the work permitted under this classification includes placement of the manufactured housing on a permanent or temporary foundation, securing the units together if required, securing the manufactured housing to the foundation, and connection of the utilities from the near proximity, such as a meter, to the manufactured housing unit and construction of foundations of less than four feet six inches in height. Work excluded from this classification includes site preparation or finishing, excavation of the ground in the area where a foundation is to be constructed, back filling and grading around the foundation, construction of foundations of more than four feet six inches in height and construction of utility services from the utility source to and including the meter or meters if required or if not required to the near proximity of the manufactured housing unit from which they are connected to the unit.
I101 - General Engineering Trades Instruction Facility. A General Engineering Trades Instruction Facility is a construction trades instruction facility authorized to teach the construction trades and is subject to the scope of practice defined in Subsection 58-55-102(22).
I102 - General Building Trades Instruction Facility. A General Building Trades Instruction Facility is a construction trades instruction facility authorized to teach the construction trades and is subject to the scope of practice defined in Subsections 58-55-102(21) or 58-55-102(32).
I103 - Electrical Trades Instruction Facility. An Electrical Trades Instruction Facility is a construction trades instruction facility authorized to teach the electrical trades and subject to the scope of practice defined in Subsection R156-55a-301(S200).
I104 - Plumbing Trades Instruction Facility. A Plumbing Trades Instruction Facility is a construction trades instruction facility authorized to teach the plumbing trades and subject to the scope of practice defined in Subsection R156-55a-301(S210).
I105 - Mechanical Trades Instruction Facility. A Mechanical Trades Instruction Facility is a construction trades instruction facility authorized to teach the mechanical trades and subject to the scope of practice defined in Subsection R156-55a-301(S350).
S200 - General Electrical Contractor. Fabrication, construction, and/or installation of generators, transformers, conduits, raceways, panels, switch gear, electrical wires, fixtures, appliances, or apparatus which utilizes electrical energy. The General Electrical Contractor scope of practice does not include activities described in this Subsection under specialty classification S354-Radon Mitigation Contractor unless the work is performed under the immediate supervision of an employee who holds a current certificate issued by the National Radon Safety Board (NRSB) or the National Radon Proficiency Program (NEHA-NRPP).
S201 - Residential Electrical Contractor. Fabrication, construction, and/or installation of services, disconnecting means, grounding devices, panels, conductors, load centers, lighting and plug circuits, appliances and fixtures in any residential unit, normally requiring non-metallic sheathed cable, including multiple units up to and including a four-plex, but excluding any work generally recognized in the industry as commercial or industrial.
S202 - Solar Photovoltaic Contractor. Fabrication, construction, installation, and replacement of photovoltaic cell panels and related components. Wiring, connections and wire methods as governed in the National Electrical Code and Subsection R156-55b-102(1) shall only be performed by an S200 General Electrical Contractor or S201 Residential Electrical Contractor. This classification is not required to install stand alone solar systems that do not tie into premises wiring or into the electrical utility, such as signage or street or parking lighting.
S210 - General Plumbing Contractor. Fabrication and/or installation of material and fixtures to create and maintain sanitary conditions in buildings, by providing a permanent means for a supply of safe and pure water, a means for the timely and complete removal from the premises of all used or contaminated water, fluid and semi-fluid organic wastes and other impurities incidental to life and the occupation of such premises, and provision of a safe and adequate supply of gases for lighting, heating, and industrial purposes. Work permitted under this classification shall include the furnishing of materials, fixtures and labor to extend service from a building out to the main water, sewer or gas pipeline. The General Plumbing Contractor scope of practice does not include activities described in this Subsection under specialty classification S354-Radon Mitigation Contractor unless the work is performed under the immediate supervision of an employee who holds a current certificate issued by the National Radon Safety Board (NRSB) or the National Radon Proficiency Program (NEHA-NRPP).
S211 - Boiler Installation Contractor. Fabrication and/or installation of commercial type fire-tube and water-tube power boilers and hot water heating boilers, including all fittings and piping, valves, gauges, pumps, radiators, converters, fuel oil tanks, fuel lines, chimney flues, heat insulation and all other devices, apparatus, and equipment related thereto. The supply line of potable water up to and including installation of the backflow prevention device must be performed by a licensed plumbing contractor. Residential boilers and water heater installation is not allowed under this classification.
S212 - Irrigation Sprinkling Contractor. Layout, fabrication, and/or installation of water distribution system for artificial watering or irrigation.
S213 - Industrial Piping Contractor. Fabrication and/or installation of pipes and piping for the conveyance or transmission of steam, gases, chemicals, and other substances including excavating, trenching, and back-filling related to such work. This classification includes the above work for geo thermal systems.
S214 - Water Conditioning Equipment Contractor. Fabrication and/or installation of water conditioning equipment and only such pipe and fittings as are necessary for connecting the water conditioning equipment to the water supply system within the premises.
S215 - Solar Thermal Systems Contractor. Construction, repair and/or installation of solar thermal systems up to the system shut off valve or where the system interfaces with any other plumbing system.
S216 - Residential Sewer Connection and Septic Tank Contractor. Construction of residential sewer lines including connection to the public sewer line, and excavation and grading related thereto. Excavation, installation and grading of residential septic tanks and their drainage.
S217 - Residential Plumbing Contractor. Fabrication and/or installation of material and fixtures to create and maintain sanitary conditions in residential building, including multiple units up to and including a four-plex by providing a permanent means for a supply of safe and pure water, a means for the timely and complete removal from the premises of all used or contaminated water, fluid and semi-fluid organic wastes and other impurities incidental to life and the occupation of such premises, and provision of a safe and adequate supply of gases for lighting and heating purposes. Work permitted under this classification shall include the furnishing of materials, fixtures and labor to extend service from a residential building out to the main water, sewer or gas pipeline. Excluded is any new construction and service work generally recognized in the industry as commercial or industrial.
S220 - Carpentry Contractor. Fabrication for structural and finish purposes in a structure or building using wood, wood products, metal studs, vinyl materials, or other wood/plastic/metal composites as is by custom and usage accepted in the building industry as carpentry. Incidental work includes the installation of tub liners and wall systems.
S221 - Cabinet, Millwork and Countertop Installation Contractor. On-site construction and/or installation of milled wood products or countertops.
S222 - Overhead and Garage Door Contractor. The installation of overhead and garage doors and door openers.
S230 - Siding Contractor. Fabrication, construction, and/or installation of siding.
S231 - Raingutter Installation Contractor. On-site fabrication and/or installation of raingutters and drains, roof flashings, gravel stops and metal ridges.
S240 - Glass and Glazing Contractor. Fabrication, construction, installation, and/or removal of all types and sizes of glass, mirrors, substitutes for glass, glass-holding members, frames, hardware, and other incidental related work.
S250 - Insulation Contractor. Installation of any insulating media in buildings and structures for the sole purpose of temperature control, sound control or fireproofing, but shall not include mechanical insulation of pipes, ducts or conduits.
S260 - General Concrete Contractor. Fabrication, construction, mixing, batching, and/or installation of concrete and related concrete products along with the placing and setting of screeds for pavement for flatwork, the construction of forms, placing and erection of steel bars for reinforcing and application of plaster and other cement-related products.
S261 - Concrete Form Setting and Shoring Contractor. Fabrication, construction, and/or installation of forms and shoring material; but, does not include the placement of concrete, finishing of concrete or embedded items such as metal reinforcement bars or mesh.
S262 - Gunnite and Pressure Grouting Contractor. Installation of a concrete product either injected or sprayed under pressure.
S263 - Cementatious Coating Systems Resurfacing and Sealing Contractor. Fabrication, construction, mixing, batching and installation of cementatious coating systems or sealants limited to the resurfacing or sealing of existing surfaces, including the preparation or patching of the surface to be covered or sealed.
S270 - General Drywall and Plastering Contractor. Fabrication, construction, and installation of drywall, gypsum, wallboard panels and assemblies. Preparation of drywall or plaster surfaces for suitable painting or finishing. Application to surfaces of coatings made of plaster, including the preparation of the surface and the provision of a base. This does not include applying stucco to lathe, plaster and other surfaces. Exempted is the plastering of foundations.
S272 - Ceiling Grid Systems, Ceiling Tile and Panel Systems Contractor. Fabrication and/or installation of wood, mineral, fiber, and other types of ceiling tile and panels and the grid systems required for placement.
S273 - Light-weight Metal and Non-bearing Wall Partitions Contractor. Fabrication and/or installation of light-weight metal and other non-bearing wall partitions.
S280 - General Roofing Contractor. Application and/or installation of asphalt, pitch, tar, felt, flax, shakes, shingles, roof tile, slate, and any other material or materials, or any combination of any thereof which use and custom has established as usable for, or which are now used as, water-proof, weatherproof, or watertight seal or membranes for roofs and surfaces; and roof conversion. Incidental work includes the installation of roof clamp ring to the roof drain.
S290 - General Masonry Contractor. Construction by cutting, and/or laying of all of the following brick, block, or forms: architectural, industrial, and refractory brick, all brick substitutes, clay and concrete blocks, terra-cotta, thin set or structural quarry tile, glazed structural tile, gypsum tile, glass block, clay tile, copings, natural stone, plastic refractories, and castables and any incidental works, including the installation of shower pans, as required in construction of the masonry work.
S291 - Stone Masonry Contractor. Construction using natural or artificial stone, either rough or cut and dressed, laid at random, with or without mortar. Incidental work includes the installation of shower pans.
S292 - Terrazzo Contractor. Construction by fabrication, grinding, and polishing of terrazzo by the setting of chips of marble, stone, or other material in an irregular pattern with the use of cement, polyester, epoxy or other common binders. Incidental work includes the installation of shower pans.
S293 - Marble, Tile and Ceramic Contractor. Preparation, fabrication, construction, and installation of artificial marble, burned clay tile, ceramic, encaustic, falence, quarry, semi-vitreous, and other tile, excluding hollow or structural partition tile. Incidental work includes the installation of shower pans.
S294 - Cultured Marble Contractor. Preparation, fabrication and installation of slab and sheet manmade synthetic products including cultured marble, onyx, granite, onice, corian, and corian type products. Incidental work includes the installation of shower pans.
S300 - General Painting Contractor. Preparation of surface and/or the application of all paints, varnishes, shellacs, stains, waxes and other coatings or pigments.
S310 - Excavation and Grading Contractor. Moving of the earth's surface or placing earthen materials on the earth's surface, by use of hand or power machinery and tools, including explosives, in any operation of cut, fill, excavation, grading, trenching, backfilling, or combination thereof as they are generally practiced in the construction trade.
S320 - Steel Erection Contractor. Construction by fabrication, placing, and tying or welding of steel reinforcing bars or erecting structural steel shapes, plates of any profile, perimeter or cross-section that are used to reinforce concrete or as structural members, including riveting, welding, and rigging.
S321 - Steel Reinforcing Contractor. Fabricating, placing, tying, or mechanically welding of reinforcing bars of any profile that are used to reinforce concrete buildings or structures.
S322 - Metal Building Erection Contractor. Erection of pre-fabricated metal structures including concrete foundation and footings, grading, and surface preparation.
S323 - Structural Stud Erection Contractor. Fabrication and installation of metal structural studs and bearing walls.
S330 - Landscaping Contractor.
(a) grading and preparing land for architectural, horticultural, or decorative treatment;
(b) arrangement, and planting of gardens, lawns, shrubs, vines, bushes, trees, or other decorative vegetation;
(c) construction of small decorative pools, tanks, fountains, hothouses, greenhouses, fences, walks, garden lighting of 50 volts or less, or sprinkler systems;
(d) construction of retaining walls except retaining walls which are intended to hold vehicles, structures, equipment or other non natural fill materials within the area located within a 45 degree angle from the base of the retaining wall to the level of where the additional weight bearing vehicles, structures, equipment or other non natural fill materials are located; or
(e) patio areas except that:
(i) no decking designed to support humans or structures shall be included; and
(ii) no concrete work designed to support structures to be placed upon the patio shall be included.
(f) This classification does not include running electrical or gas lines to any appliance.
S340 - Sheet Metal Contractor. Layout, fabrication, and installation of air handling and ventilating systems. All architectural sheet metal such as cornices, marquees, metal soffits, gutters, flashings, and skylights and skydomes including both plastic and fiberglass.
S350 - HVAC Contractor. Fabrication and installation of complete warm air heating and air conditioning systems, and complete ventilating systems. The HVAC Contractor scope of practice does not include activities described in this Subsection under specialty classification S354-Radon Mitigation Contractor unless the work is performed under the immediate supervision of an employee who holds a current certificate issued by the National Radon Safety Board (NRSB) or the National Radon Proficiency Program (NEHA-NRPP). Installation of water heaters or any boiler system is not allowed under this classification.
S351 - Refrigerated Air Conditioning Contractor. Fabrication and installation of air conditioning ventilating systems to control air temperatures below 50 degrees.
S352 - Evaporative Cooling Contractor. Fabrication and installation of devices, machinery, and units to cool the air temperature employing evaporation of liquid.
S353 - Warm Air Heating Contractor. Layout, fabrication, and installation of such sheet metal, gas piping, and furnace equipment as necessary for a complete warm air heating and ventilating system.
S354 - Radon Mitigation Contractor. Layout, fabrication, and installation of a radon mitigation system. This classification does not include work on heat recovery ventilation or makeup air components which must be performed by an HVAC Contractor and does not include electrical wiring which must be performed by an Electrical Contractor.
S360 - Refrigeration Contractor. Construction and/or installation of refrigeration equipment including, but not limited to, built-in refrigerators, refrigerated rooms, insulated refrigerated spaces and equipment related thereto; but, the scope of permitted work does not include the installation of gas fuel or electric power services other than connection of electrical devices to a junction box provided for that device and electrical control circuitry not exceeding 50 volts.
S370 - Fire Suppression Systems Contractor. Layout, fabrication, and installation of fire protection systems using water, steam, gas, or chemicals. When a potable sanitary water supply system is used as the source of supply, connection to the water system must be accomplished by a licensed journeyman plumber. Excluded from this classification are persons engaged in the installation of fire suppression systems in hoods above cooking appliances.
S380 - Swimming Pool and Spa Contractor. On-site fabrication, construction and installation of swimming pools, prefabricated pools, spas, and tubs.
S390 - Sewer and Waste Water Pipeline Contractor. Construction of sewer lines, sewage disposal and sewage drain facilities including excavation and grading with respect thereto, and the construction of sewage disposal plants and appurtenances thereto.
S400 - Asphalt Paving Contractor. Construction of asphalt highways, roadways, driveways, parking lots or other asphalt surfaces, which will include but will not be limited to, asphalt overlay, chip seal, fog seal and rejuvenation, micro surfacing, plant mix sealcoat, slurry seal, and the removal of asphalt surfaces by milling. Also included is the excavation, grading, compacting and laying of fill or base-related thereto. Also included in painting on asphalt surfaces including striping, directional and other types of symbols or words.
S410 - Pipeline and Conduit Contractor. Fabrication, construction, and installation of pipes, conduit or cables for the conveyance and transmission from one station to another of such products as water, steam, gases, chemicals, slurries, data or communications. Included are the excavation, cabling, horizontal boring, grading, and backfilling necessary for construction of the system.
S420 - General Fencing, Ornamental Iron and Guardrail Contractor. Fabrication, construction, and installation of fences, guardrails, handrails, and barriers.
S421 - Residential Fencing Contractor. Fabrication and installation of residential fencing up to and including a height of six feet.
S430 - Metal Firebox and Fuel Burning Stove Installer. Fabrication, construction, and installation of metal fireboxes, fireplaces, and wood or coal-burning stoves, including the installation of venting and exhaust systems, provided the individual performing the installation is RMGA certified.
S440 - Sign Installation Contractor. Installation of signs and graphic displays which require installation permits or permission as issued by state or local governmental jurisdictions. Signs and graphic displays shall include signs of all types, both lighted and unlighted, permanent highway marker signs, illuminated awnings, electronic message centers, sculptures or graphic representations including logos and trademarks intended to identify or advertise the user or his product, building trim or lighting with neon or decorative fixtures, or any other animated, moving or stationary device used for advertising or identification purposes. Signs and graphic displays must be fabricated, installed and erected in accordance with professionally engineered specifications and wiring in accordance with the National Electrical Code.
S441 - Non Electrical Outdoor Advertising Sign Contractor. Installation of signs and graphic displays which require installation permits or permission as issued by state and local governmental jurisdictions. Signs and graphics shall include outdoor advertising signs which do not have electrical lighting or other electrical requirements, and in accordance with professionally engineered specifications.
S450 - Mechanical Insulation Contractor. Fabrication, application and installation of insulation materials to pipes, ducts and conduits.
S460 - Wrecking and Demolition Contractor. The raising, cribbing, underpinning, moving, and removal of building and structures.
S470 - Petroleum Systems Contractor. Installation of above and below ground petroleum and petro-chemical storage tanks, piping, dispensing equipment, monitoring equipment and associated petroleum and petro-chemical equipment including excavation, backfilling, concrete and asphalt.
S480 - Piers and Foundations Contractor. The excavation, drilling, compacting, pumping, sealing and other work necessary to construct, alter or repair piers, piles, footings and foundations placed in the earth's subsurface to prevent structural settling and to provide an adequate capacity to sustain or transmit the structural load to the soil or rock below.
S490 - Wood Flooring Contractor. Installation of wood flooring including prefinished and unfinished material, sanding, staining and finishing of new and existing wood flooring. Underlayments, non-structural subfloors and other incidental related work.
S491 - Laminate Floor Installation Contractor. Installation of laminate floors including underlayments, non-structural subfloors and other incidental related work, but does not include the installation of sold wood flooring.
S500 - Sports and Athletic Courts, Running Tracks, and Playground Installation Contractor. Installation of sports and athletic courts including but not limited to tennis courts, racquetball courts, handball courts, basketball courts, running tracks, playgrounds, or any combination. Includes nonstructural floor subsurfaces, nonstructural wall surfaces, perimeter walls and perimeter fencing. Includes the installation and attachment of equipment such as poles, basketball standards or other equipment.
S510 - Elevator Contractor. Erecting, constructing, installing, altering, servicing, repairing or maintaining an elevator.
S600 - General Stucco Contractor. Applying stucco to lathe, plaster and other surfaces.
S700 - Specialty License Contractor.
(a) A specialty license is a license that confines the scope of the allowable contracting work to a specialized area of construction which the Division grants on a case-by-case basis.
(b) When applying for a specialty license, an applicant, if requested, shall submit to the Division the following:
(i) a detailed statement of the type and scope of contracting work that the applicant proposes to perform; and
(ii) any brochures, catalogs, photographs, diagrams, or other material to further clarify the scope of the work that the applicant proposes to perform.
(c) A contractor issued a specialty license shall confine the contractor's activities to the field and scope of operations as outlined by the Division.
(3) The scope of practice for the following primary classifications includes the scope of practice stated in the descriptions for the following subsclassifications:
TABLE I
Primary Classification Included subclassifications
S200 S201, S202
S210 S211, S212, S213, S214, S215,
S216, S217
S220 S221, S222
S230 S231
S260 S261, S262, S263
S270 S272, S273
S290 S291, S292, S293, S294
S320 S321, S322, S323
S350 S351, S325, S353, S354
S420 S421
S440 S441
S490 S491
(4) The following activities are determined to not significantly impact the public health, safety and welfare and therefore do not require a contractors license:
(a) sandblasting;
(b) pumping services;
(c) tree stump or tree removal;
(d) installation within a building of communication cables including phone and cable television;
(e) installation of low voltage electrical as described in R156-55b-102(1);
(f) construction of utility sheds, gazebos or other similar items which are personal property and not attached;
(g) building and window washing, including power washing;
(h) central vacuum systems installation;
(i) concrete cutting;
(j) interior decorating;
(k) wall paper hanging;
(l) drapery and blind installation;
(m) welding on personal property which is not attached;
(n) chimney sweepers other than repairing masonry;
(o) carpet and vinyl floor installation; and
(p) artificial turf installation.
(5) The following activities are those determined to not significantly impact the public health, safety and welfare beyond the regulations by other agencies and therefore do not require a contractors license:
(a) lead removal regulated by the Department of Environmental Quality;
(b) asbestos removal regulated by the Department of Environmental Quality; and
(c) fire alarm installation regulated by the Fire Marshal.
R156-55a-302a. Qualifications for Licensure - Examinations.
(1) In accordance with Subsection 58-55-302(1)(c), the qualifier for an applicant for licensure as a contractor or the qualifier for an applicant for licensure as a construction trades instruction facility shall pass the following examinations:
(a) the Utah Contractor Business - Law Examination; and
(b) an approved trade classification specific examination, where required in Subsection (2).
(2) An approved trade classification specific examination is required for the following contractor license classifications:
E100 - General Engineering Contractor
B100 - General Building Contractor
B200 - Modular Unit Installation Contractor
R100 - Residential and Small Commercial Contractor
R101 - Residential and Small Commercial Non Structural Remodeling and Repair Contractor
R200 - Factory Built Housing Contractor
I101 - General Engineering Trades Instruction Facility
I102 - General Building Trades Instruction Facility
I105 - Mechanical Trades Instruction Facility
S212 - Irrigation Sprinkling Contractor
S213 - Industrial Piping Contractor
S215 - Solar Thermal Systems Contractor
S216 - Residential Sewer Connection and Septic Tank Contractor
S220 - Carpentry Contractor
S222 - Overhead and Garage Door Contractor
S230 - Siding Contractor
S240 - Glass and Glazing Contractor
S250 - Insulation Contractor
S260 - General Concrete Contractor
S270 - General Drywall and Plastering Contractor
S280 - General Roofing Contractor
S290 - General Masonry Contractor
S293 - Marble, Tile and Ceramic Contractor
S300 - General Painting Contractor
S310 - Excavation and Grading Contractor
S320 - Steel Erection Contractor
S321 - Steel Reinforcing Contractor
S330 - Landscaping Contractor
S340 - Sheet Metal Contractor
S350 - HVAC Contractor
S351 - Refrigerated Air Conditioning Contractor
S353 - Warm Air Heating Contractor
S360 - Refrigeration Contractor
S370 - Fire Suppression Systems Contractor
S380 - Swimming Pool and Spa Contractor
S390 - Sewer and Waste Water Pipeline Contractor
S410 - Pipeline and Conduit Contractor
S440 - Sign Installation Contractor
S450 - Mechanical Insulation Contractor
S490 - Wood Flooring Contractor
S600 - General Stucco Contractor
(3) The passing score for each examination is 70%.
(4) Qualifications to sit for examination.
(a) An applicant applying to take any examination specified in this Section must sign an affidavit verifying that an applicant has completed the experience required under Subsection R156-55a-302b.
(5) "Approved trade classification specific examination" means a trade classification specific examination:
(a) given, currently or in the past, by the Division's contractor examination provider; or
(b) given by another state if the Division has determined the examination to be substantially equivalent.
(6) An applicant for licensure who fails an examination may retake the failed examination as follows:
(a) no sooner than 30 days following any failure up to three failures; and
(b) no sooner than six months following any failure thereafter.
R156-55a-302b. Qualifications for Licensure - Experience Requirements.
In accordance with Subsection 58-55-302(1)(e)(ii), the minimum experience requirements are established as follows:
(1) Requirements for all license classifications:
(a) Unless otherwise provided in this rule, all experience shall be lawfully performed under the general supervision of a contractor licensed in the classification applied for or a substantially equivalent classification, and shall be subject to the following:
(i) If the experience was completed in Utah, it shall be:
(A) completed while a W-2 employee of a licensed contractor; or
(B) completed while working as an owner of a licensed contractor, which has for all periods of experience claimed, employed a qualifier who performed the duties and served in the capacities specified in Subsection 58-55-304(4) and in Subsection R156-55a-304.
(ii) If the experience was completed outside of the state of Utah, it shall be:
(A) completed in compliance with the laws of the jurisdiction in which the experience is completed; and
(B) completed with supervision that is substantially equivalent to the supervision that is required in Utah.
(iii) Experience may be determined to be substantially equivalent if lawfully obtained in a setting which has supervision of qualified persons and an equivalent scope of work, such as performing construction activities in the military where licensure is not required.
(b) All experience shall be directly related to the scope of practice set forth in Section R156-55a-301 of the classification the applicant is applying for, as determined by the Division.
(c) One year of work experience means 2000 hours.
(d) No more than 2000 hours of experience during any 12 month period may be claimed.
(e) Except as described in Subsection (2)(c), experience obtained under the supervision of a construction trades instructor as a part of an educational program is not qualifying experience for a contractors license.
(2) Requirements for E100 General Engineering, B100 General Building, R100 Residential and Small Commercial Building license classifications:
(a) In addition to the requirements of paragraph (1), an applicant for an R100, B100 or E100 license shall have within the past 10 years a minimum of four years experience.
(b) Two of the required four years of experience shall be in a supervisory or managerial position.
(c) A person holding a four year bachelors degree or a two year associates degree in Construction Management may have one year of experience credited towards the supervisory or managerial experience requirement.
(d) A person holding a Utah professional engineer license may be credited with satisfying one year toward the supervisory or managerial experience required for E100 contractor license.
(3) Requirements for S211 Boiler Installation, S220 Carpentry, S280 General Roofing, S290 General Masonry, S320 Steel Erection, S350 Heating Ventilating and Air Conditioning, S360 Refrigeration and S370 Fire Suppression Systems license classifications:[
] In addition to the requirements of paragraph (1), an applicant shall have within the past 10 years a minimum of four years of experience.
(4) Requirements for I101 General Engineering Trades Instruction Facility, I102 General Building Trades Instruction Facility, I103 Electrical Trades Instruction Facility, I104 Plumbing Trades Instruction Facility, I105 Mechanical Trades Instruction Facility license classifications:
An applicant for construction trades instruction facility license shall have the same experience that is required for the license classifications for the construction trade they will instruct.
(5) Requirements for other license classifications:
Except as set forth in Subsections (6) and (7), in addition to the requirements of paragraph (1), an applicant for contractor license classification not listed above shall have within the past 10 years a minimum of two years of experience.
(6) Requirements for S202 Solar Photovoltaic Contractor. In addition to the requirements of Subsections (1) and (5), an applicant shall hold a current certificate by the North American Board of Certified Energy Practitioners.
(7) Requirements for S354 Radon Mitigation Contractor. In addition to the requirements of Subsections (1) and (5), an applicant shall hold a current certificate issued by the National Radon Safety Board (NRSB) or the National Radon Proficiency Program (NEHA-NRPP). Experience completed prior to the effective date of this rule does not need to be performed under the supervision of a licensed contractor. Experience completed after the effective date of this rule must be performed under the supervision of a licensed contractor who has authority to practice radon mitigation.
(8) Requirements for S211 Boiler Installation Contractor. The experience required under Subsection R156-55a-302b(3) for the S211 Boiler Installation Contractor shall be demonstrated by the qualifier being a currently active and licensed master plumber or shall include four years experience installing commercial type boilers.
KEY: contractors, occupational licensing, licensing
Date of Enactment or Last Substantive Amendment: [July 9, ]2012
Notice of Continuation: October 4, 2011
Authorizing, and Implemented or Interpreted Law: 58-1-106(1)(a); 58-1-202(1)(a); 58-55-101; 58-55-308(1)(a); 58-55-102(39)(a)
Additional Information
The Portable Document Format (PDF) version of the Bulletin is the official version. The PDF version of this issue is available at https://rules.utah.gov/publicat/bull-pdf/2012/b20120915.pdf. The HTML edition of the Bulletin is a convenience copy. Any discrepancy between the PDF version and HTML version is resolved in favor of the PDF version.
Text to be deleted is struck through and surrounded by brackets (e.g., [example]). Text to be added is underlined (e.g., example). Older browsers may not depict some or any of these attributes on the screen or when the document is printed.
For questions regarding the content or application of this rule, please contact Dan Jones at the above address, by phone at 801-530-6720, by FAX at 801-530-6511, or by Internet E-mail at [email protected].