DAR File No. 36733

This rule was published in the January 1, 2013, issue (Vol. 2013, No. 1) of the Utah State Bulletin.


Environmental Quality, Air Quality

Rule R307-351

Graphic Arts

Change in Proposed Rule

DAR File No.: 36733
Filed: 12/10/2012 12:57:08 PM

RULE ANALYSIS

Purpose of the rule or reason for the change:

During the public comment period, industry and EPA both submitted comments that resulted in the need to make substantive changes to the definitions section and record-keeping requirements of the rule.

Summary of the rule or change:

Language is added throughout the rule to require owners and operators of emission control devices to provide documentation that their emission control devices will meet the requirements of the rule. Owners and operators of emission control devices are now required to maintain for a minimum of two years records to demonstrate that the equipment is being operated and maintained in accordance with manufacturer recommendations, and these records must be made available to the director upon request. Clarifying language is added to the definition of "Blanket", a definition for "composite partial vapor pressure" is added, and the definition for "Gravure" is removed from Section R307-351-3. (DAR NOTE: This change in proposed rule has been filed to make additional changes to a proposed new rule that was published in the October 1, 2012, issue of the Utah State Bulletin, on page 80. Underlining in the rule below indicates text that has been added since the publication of the proposed rule mentioned above; strike-out indicates text that has been deleted. You must view the change in proposed rule and the proposed new rule together to understand all of the changes that will be enforceable should the agency make this rule effective.)

State statutory or constitutional authorization for this rule:

  • Subsection 19-2-104(1)(a)

Anticipated cost or savings to:

the state budget:

There are no new requirements for the state; therefore, there are no anticipated costs or savings.

local governments:

There are no new requirements for local governments; therefore, there are no anticipated costs or savings.

small businesses:

The added record-keeping requirements will likely result in increased costs to small businesses; however, those costs should be minimal.

persons other than small businesses, businesses, or local governmental entities:

There are no new requirements to persons other than small businesses, businesses, or local government entities; therefore, there are no anticipated costs or savings.

Compliance costs for affected persons:

The added record-keeping requirements will likely result in increased compliance costs; however, those costs should be minimal.

Comments by the department head on the fiscal impact the rule may have on businesses:

The added record-keeping requirements will likely result in increased compliance costs to businesses; however, those costs should be minimal.

Amanda Smith, Executive Director

The full text of this rule may be inspected, during regular business hours, at the Division of Administrative Rules, or at:

Environmental Quality
Air QualityRoom Fourth Floor
195 N 1950 W
SALT LAKE CITY, UT 84116-3085

Direct questions regarding this rule to:

  • Mark Berger at the above address, by phone at 801-536-4000, by FAX at 801-536-0085, or by Internet E-mail at mberger@utah.gov

Interested persons may present their views on this rule by submitting written comments to the address above no later than 5:00 p.m. on:

This rule may become effective on:

02/01/2013

Authorized by:

Bryce Bird, Director

RULE TEXT

R307. Environmental Quality, Air Quality.

R307-351. Graphic Arts.

R307-351-1. Purpose.

The purpose of this rule is to limit volatile organic compound (VOC) emissions from graphic arts printing operations.

 

R307-351-2. Applicability.

R307-351 applies to graphic arts printing operations in Box Elder, Cache, Davis, Salt Lake, Utah and Weber counties as specified below. For purposes of determining whether the emissions applicability threshold or an equivalent threshold is met, the owner or operator shall consider source-wide emissions from all printing operations including related cleaning activities prior to controls.

(1) R307-351-4 applies to all packaging and publication rotogravure; packaging and publication flexographic; and specialty printing operations employing [solvent]VOC-[ ]containing inks, including dilution and cleaning [solvents]materials, that have potential to emit on a per press basis equal to or greater than 25 tons per year of VOC. Flexible packaging printing is exempt from R307-351-4.

(2) R307-351-5 applies to all flexible packaging printing operations with potential to emit on a per press basis, from the dryer, prior to controls, equal to or greater than 25 tons per year of VOC [(petroleum ink oil)] from inks, coatings and adhesives combined.

(3) R307-351-6(1) applies to individual heatset web offset lithographic printing presses and individual heatset web letterpress printing presses with potential to emit from the dryer, on a per press basis, prior to controls, equal to or greater than 25 tons per year of VOC[(petroleum ink oil)]. Heatset presses used for book printing and heatset presses with maximum web width of 22 inches or less are exempt from R307-351-6(1).

(4) R307-351-6(2) applies to offset lithographic printing operations that emit at least 2.7 tons per year actual emissions of VOC, or an equivalent level, before consideration of controls. Any press with total fountain solution reservoir of less than one gallon and sheet-fed presses with maximum sheet size of 11 inches by 17 inches or smaller are exempt from R307-351-6(2).

(5) R307-351-6(3) applies to offset lithographic printing and letterpress printing operations that emit at least 2.7 tons per year actual emissions of VOC, or an equivalent level, before consideration of controls. Cleaners used on electronic components of a press, pre-press cleaning operations (e.g., platemaking), post-press cleaning operations (e.g., binding), cleaning supplies (e.g., detergents) used to clean the floor (other than dried ink) in the area around a press, or cleaning performed in parts washers or cold cleaners are exempt from R307-351-6(3).

(6) R307-351-7 applies to all graphic arts printing operations that emit at least 2.7 tons per year actual emissions of VOC, or an equivalent level, before consideration of controls.

 

R307-351-3. Definitions.

The following additional definitions apply to R307-351:

"Alcohol" means any of the following compounds, when used as a fountain solution additive for offset lithographic printing: ethanol, n-propanol, and isopropanol.

"Alcohol Substitute" means a nonalcohol additive that contains VOCs and is used in the fountain solution.

"Automatic Blanket Wash System" means equipment used to clean lithographic blankets which can include, but is not limited to those utilizing a cloth and expandable bladder, brush, spray, or impregnated cloth system.

"Cleaning Solution" means a liquid solvent or solution used to clean the operating surfaces of a printing press and its parts. Cleaning solutions include, but are not limited to blanket wash, roller wash, metering roller cleaner, plate cleaner, impression cylinder washes, rubber rejuvenators, and other cleaners used for cleaning a press, press parts, or to remove dried ink or coating from areas around the press.

"Blanket" [means a synthetic rubber mat used in offset-lithography to transfer or "offset" an image from a planographic printing plate to paper or other substrate]means a synthetic rubber material that is wrapped around a cylinder used in offset lithography to transfer or "offset" an image from an image carrier.

"Capture efficiency" means the fraction of all VOC emissions generated by a process that are delivered to a control device, expressed as a percentage.

"Capture system" means the equipment (including hoods, ducts, fans, etc.) used to collect, capture, or transport a pollutant to a control device.

"Coating" means material applied onto or impregnated into a substrate. Such materials include, but are not limited to, solvent-borne and waterborne coatings.

"Composite partial vapor pressure" means the sum of the partial pressure of the compounds defined as VOCs.

"Control device" means a device such as a carbon adsorber or oxidizer which reduces the VOC in an exhaust gas by recovery or by destruction.

"Control device efficiency" means the ratio of VOC emissions recovered or destroyed by a control device to the total VOC emissions that are introduced into the control device, expressed as a percentage.

"Flexible packaging" means any package or part of a package the shape of which can be readily changed. Flexible packaging includes, but is not limited to, bags, pouches, liners and wraps utilizing paper, plastic, film, aluminum foil, metalized or coated paper or film, or any combination of these materials.

"Flexographic press" means an unwind or feed section, which may include more than one unwind or feed station (such as on a laminator), a series of individual work stations, one or more of which is a flexographic print station, any dryers (including interstage dryers and overhead tunnel dryers) associated with the work stations, and a rewind, stack, or collection section. The work stations may be oriented vertically, horizontally, or around the circumference of a single large impression cylinder. Inboard and outboard work stations, including those employing any other technology, such as rotogravure, are included if they are capable of printing or coating on the same substrate. A publication rotogravure press with one or more flexographic imprinters is not a flexographic press.

"Flexographic printing" means the application of words, designs, and pictures to substrate by means of a roll printing technique in which the pattern to be applied is raised above the printing roll and the image carrier is made of rubber or other elastomeric materials.

"Fountain solution" means a mixture of water and other volatile and non-volatile chemicals and additives that wets the nonimage area of a lithographic printing plate so that the ink is maintained within the image areas.

["Gravure" means a method of printing with etched plates or cylinders.

]"Heatset" means an offset lithographic printing or letterpress printing operation in which the ink solvents are vaporized by passing the printed surface through a dryer.

"Letterpress printing" means a method where the image area is raised relative to the non-image area and the ink is transferred to the substrate directly from the image surface.

"Narrow-web flexographic press" means a flexographic press that is not capable of printing substrates greater than 18 inches in width and that does not also meet the definition of rotogravure press (i.e., it has no rotogravure print stations).

"Non-heatset", also called coldset, means an offset lithographic printing or letterpress printing operation in which the ink dries by oxidation and/or absorption into the substrate without use of heat from dryers.

"Offset lithographic printing" means a plane-o-graphic method in which the image and non-image areas are on the same plane and the ink is offset from a plate to a rubber blanket, and then from the blanket to the substrate.

"Overall control efficiency" means the total efficiency of a control system, determined either by:

(1) The product of the capture efficiency and the control device efficiency; or

(2) A liquid-liquid material balance.

"Packaging printing" means rotogravure or flexographic printing, not otherwise defined as publication printing, upon paper, paper board, metal foil, plastic film, and other substrates, which are, in subsequent operations, formed into packaging products and labels. This includes, but is not limited to, folding cartons, flexible packaging, labels and wrappers.

"Printing operation" means the application of words, designs, or pictures on a substrate. All units in a machine which have both coating and printing units shall be considered as performing a printing operation.

"Printing Press" means a printing production assembly composed of one or more units used to produce a printed substrate, including but not limited to, any associated coating, spray powder application, heatset web dryer, ultraviolet or electron beam curing units, or infrared heating units.

"Publication rotogravure printing" means rotogravure printing upon paper that is subsequently formed into books, magazines, catalogues, brochures, directories, newspaper supplements, and other types of printed materials.

"Publication rotogravure press" means a rotogravure press used for publication rotogravure printing. A publication rotogravure press may include one or more flexographic imprinters. A publication rotogravure press with one or more flexographic imprinters is not a flexographic press.

"Roll coating" means the application of a coating material to a substrate by means of hard rubber or steel rolls.

"Roll printing" means the application of words, designs and pictures to a substrate usually by means of a series of hard rubber or steel rolls each with only partial coverage.

"Rotogravure coating" means the application of a uniform layer of material across the entire width of the web to substrate by means of a roll coating technique in which the pattern to be applied is etched on the coating roll. The coating material is picked up in these recessed areas and is transferred to the substrate.

"Rotogravure press" means an unwind or feed section, which may include more than one unwind or feed station (such as on a laminator), a series of individual work stations, one or more of which is a rotogravure print station, any dryers associated with the work stations, and a rewind, stack, or collection section. Inboard and outboard work stations, including those employing any other technology, such as flexography, are included if they are capable of printing or coating on the same substrate.

"Rotogravure printing" means the application of words, designs, and pictures to a substrate by means of a roll printing technique that involves a recessed image area in the form of cells.

"Specialty printing operations" means all gravure and flexographic operations that print a design or image, excluding publication and packaging printing. Specialty printing operations include, among other things, printing on paper cups and plates, patterned gift wrap, wallpaper, and floor coverings.

"Web" means a continuous roll of substrate.

"Wide-web flexographic press" means a flexographic press capable of printing substrates greater than 18 inches in width.

 

R307-351-4. Standards for Rotogravure, Flexographic, and Specialty Printing Operations.

(1) No owner or operator of a packaging and publication rotogravure; packaging and publication flexographic, and specialty printing operations employing [solvent]VOC-[ ]containing ink may operate, cause, or allow or permit the operation of a facility unless:

(a) The volatile fraction of ink, as it is applied to the substrate, contains 25.0% by volume or less of VOC[organic solvent] and 75.0% by volume or more of water; or

(b) The ink as it is applied to the substrate, less water, contains 60.0% by volume or more nonvolatile material; or

(c) The owner or operator installs and operates either a carbon adsorption system as described in R307-351-4(1)(a)(i) or an incineration system as described in R307-351-4(1)(a)(ii).[ A capture system as described in R307-351-4(1)(a)(iii) shall be used in conjunction with a carbon adsorption system and an incineration system.]

(i) A carbon adsorption system shall reduce the volatile organic emissions from the capture system by a minimum of 90.0% by weight.

(ii) An incineration system shall oxidize, from the capture system, a minimum of 90.0% of the non-methane VOCs measured as total combustible carbon to carbon dioxide and water.

(iii) A capture system as described in R307-351-4(1)(a)(iv) shall be used in conjunction with a carbon adsorption system and an incineration system.

([iii]iv) The design and operation of a capture system must be consistent with good engineering practices and shall be required to provide for an overall reduction in VOC emissions of at least:

(A) 75.0% where a publication rotogravure process is employed;

(B) 65.0% where a packaging rotogravure process is employed; or

(C) 60.0% where a flexographic printing process is employed.

(2) The owner or operator of an emission control device shall provide documentation that the system will attain the requirements of R307-351-4.

(3) The Emission control system shall be operated and maintained in accordance with the manufacturer recommendations.

(4) The owner or operator of an emission control device shall maintain for a minimum of two years records of operating and maintenance sufficient to demonstrate that the equipment is being operated and maintained in accordance with the manufacturer recommendations.

 

R307-351-5. Standards for Flexible Packaging Printing Operations.

(1) Presses used for flexible packaging printing shall comply with an 80% overall emission control efficiency.

(a) The owner or operator of an emission control device shall provide documentation that the emissions control system will attain the requirements of R307-351-5.

(b) The Emission control system shall be operated and maintained in accordance with the manufacturer recommendations.

(2) The owner or operator of an emission control device shall maintain for a minimum of two years records of operating and maintenance sufficient to demonstrate that the equipment is being operated and maintained in accordance with the manufacturer recommendations.

([2]3) As an alternative to the overall control efficiency, the following two equivalent VOC content limits may be met by use of low VOC content materials or combinations of materials and controls as follows:

([i]a) 0.8 kg VOC/kg solids applied; or

([ii]b) 0.16 kg VOC/kg materials applied.

([iii]c) The VOC content limits can be met by averaging the VOC content of materials used on a single press, i.e., within a line. The use of averaging to meet the VOC content limits is not allowed for cross-line, i.e., across multiple lines.

 

R307-351-6. Standards for Offset Lithographic Printing and Letterpress Printing Operations.

(1) Requirements for heatset web offset lithographic and heatset letterpress inks and dryers.

(a) Individual heatset web offset lithographic printing presses and individual heatset web letterpress printing presses shall comply with [a] 90% control efficiency for the control device on heatset dryers.

(b) The owner or operator of an emission control device shall provide documentation that the emissions control system will attain the requirements of R307-351-6.

(c) The Emission control system shall be operated and maintained in accordance with the manufacturer recommendations.

(2) The owner or operator shall maintain for a minimum of two years records of operating and maintenance sufficient to demonstrate that the equipment is being operated and maintained in accordance with the manufacturer recommendations.

([b]3) As an alternative to the control efficiency, the control device outlet concentration may be reduced to 20 ppmv as hexane on a dry basis to accommodate situations where the inlet VOC concentration is low or there is no identifiable measurable inlet.

([2]4) Requirements for fountain solution.

(a) For heatset web offset lithographic printing, the level of control for VOC emissions from on-press (as-applied) fountain solution shall meet one of the following:

(i) 1.6% alcohol or less (by weight) in the fountain;

(ii) 3.0% alcohol or less (by weight) [on-press (as-applied) ]in the fountain solution if the fountain solution is refrigerated to below 60 degrees Fahrenheit; or

(iii) 5.0% alcohol substitute or less (by weight) [on-press (as-applied) ]and no alcohol in the fountain solution.

(b) For sheet-fed offset lithographic printing, the level of control for VOC emissions from on-press (as-applied) fountain solution shall meet one of the following:

(i) 5.0% alcohol or less (by weight) in the fountain;

(ii) 8.5% alcohol or less (by weight) [on-press (as-applied) ]in the fountain solution provided the fountain solution is refrigerated to below 60 degrees Fahrenheit; or

(iii) 5.0% alcohol substitute or less (by weight) [on-press (as-applied)] and no alcohol in the fountain solution.

(c) For non-heatset web offset lithographic printing, the level of control for VOC emissions shall be 5.0% alcohol substitute or less (by weight) on-press (as-applied) and no alcohol in the fountain solution.

([3]5) Requirements for cleaning materials.

(a) For blanket washing, roller washing, plate cleaners, metering roller cleaners, impression cylinder cleaners, rubber rejuvenators, and other cleaners used for cleaning a press, press parts, or to remove dried ink from areas around a press, only cleaning materials with a VOC composite vapor pressure of less than ten mm Hg at 68 degrees Fahrenheit or cleaning materials containing less than 70 weight percent VOC shall be used.

(b) Up to 110 gallons per year of cleaning materials which meet neither the VOC composite vapor pressure requirement nor the VOC content requirement may be used.

 

R307-351-7. Work Practices and Recordkeeping.

(1) Control techniques and work practices are to be implemented at all times to reduce VOC emissions from fugitive type sources. Control techniques and work practices include:

(a) Tight fitting covers for open tanks; and

(b) Keeping cleaning materials, used shop towels, and solvent wiping cloths in closed containers.

(2) Record keeping and reporting.

(a) The owner or operator of any source subject to R307-351 shall maintain:

(i) Records of the [monthly]annual us[e]age of all materials that may be a source of VOC emissions including, but not limited to, inks, coatings, adhesives, fountain solution, and cleaning materials[, and solvents].

(ii) [The owner or operator shall maintain records from the manufacturer that demonstrate compliance with the standards of R307-351.]All sources subject to R307-351 shall maintain records demonstrating compliance with all provisions of R307-351. These records shall be available to the director upon request.

 

[R307-351-8. Optional Add-On Controls for Coating Operations.

(1) The owner or operator of an add-on control device shall provide certification from the manufacturer that the emission control system will attain the efficiency performance specified in R307-351.

(2) Emission control systems shall be operated and maintained in accordance with the manufacturer recommendations.

(3) The owner or operator shall maintain for a minimum of two years records of operating and maintenance sufficient to demonstrate that the equipment is being operated and maintained in accordance with the manufacturer recommendations.

 

]R307-351-[9]8. Compliance Schedule.

(1) All sources within Salt Lake and Davis counties shall be in compliance with this rule by the effective date of this rule.

(2) All sources within Box Elder, Cache, Utah and Weber counties shall be in compliance with this rule by January 1, 2014.

 

KEY: air pollution, graphic arts, VOC, printing operations

Date of Enactment or Last Substantive Amendment: [2012]2013

Authorizing, and Implemented or Interpreted Law: 19-2-104(1)(a)

 


Additional Information

The Portable Document Format (PDF) version of the Bulletin is the official version. The PDF version of this issue is available at https://rules.utah.gov/publicat/bull-pdf/2013/b20130101.pdf. The HTML edition of the Bulletin is a convenience copy. Any discrepancy between the PDF version and HTML version is resolved in favor of the PDF version.

Text to be deleted is struck through and surrounded by brackets (e.g., [example]). Text to be added is underlined (e.g., example).  Older browsers may not depict some or any of these attributes on the screen or when the document is printed.

For questions regarding the content or application of this rule, please contact Mark Berger at the above address, by phone at 801-536-4000, by FAX at 801-536-0085, or by Internet E-mail at mberger@utah.gov.