Utah Administrative Code

The Utah Administrative Code is the body of all effective administrative rules as compiled and organized by the Division of Administrative Rules (see Subsection 63G-3-102(5); see also Sections 63G-3-701 and 702).

NOTE: For a list of rules that have been made effective since October 1, 2019, please see the codification segue page.

NOTE TO RULEFILING AGENCIES: Use the RTF version for submitting rule changes.


R307. Environmental Quality, Air Quality.

Rule R307-346. Metal Furniture Surface Coatings.

As in effect on October 1, 2019

Table of Contents

R307-346-1. Purpose.

The purpose of this rule is to limit volatile organic compound (VOC) emissions from metal furniture surface coating operations in application areas, flash-off areas, and ovens of metal furniture coating lines involved in prime and top-coat or single coat operations.

R307-346-2. Applicability.

(1) R307-346 applies to metal furniture surface coating operations located in Box Elder, Cache, Davis, Salt Lake, Tooele, Utah and Weber counties.

(2) Before September 1, 2018, R307-346 applies to metal furniture surface coating operations that have the potential to emit 2.7 tons per year or more of VOC, including related cleaning activities.

(3) Effective September 1, 2018, R307-346 shall apply to metal furniture surface coating operations that use a combined 20 gallons or more of coating products and associated solvents per year.

R307-346-3. Exemptions.

(1) The requirements of R307-346 do not apply to the following:

(a) Stencil coatings;

(b) Safety-indicating coatings;

(c) Solid-film lubricants;

(d) Electrical-insulating and thermal-conducting coatings;

(e) Touch-up and repair coatings; or

(f) Coating applications utilizing hand-held aerosol cans.

R307-346-4. Definitions.

The following additional definitions apply to R307-346:

"Air dried coating" means coatings that are dried by the use of air or a forced warm air at temperatures up to 194 degrees Fahrenheit.

"Application area" means the area where the coating is applied by spraying, dipping, or flow coating techniques.

"As applied" means the VOC and solids content of the finishing material that is actually used for coating the substrate. It includes the contribution of materials used for in-house dilution of the finishing material.

"Baked coating" means a coating that is cured at a temperature at or above 194 degrees Fahrenheit.

"Extreme performance coatings" means coatings designed for harsh exposure or extreme environmental conditions.

"Metal furniture surface coating" means the surface coating of any furniture made of metal or any metal part that will be assembled with other metal, wood fabric, plastic, or glass parts to form a furniture piece.

R307-346-5. VOC Content Limits.

No owner or operator shall apply coatings with a VOC content greater than the amounts specified in Table 1, unless the owner or operator uses an add-on control device as specified in R307-346-7.

                                                    TABLE 1

                                       METAL FURNITURE SURFACE COATING VOC LIMITS
                             (values in pounds of VOC per gallon of coating, minus water and
                             exempt solvents (compounds not classified as VOC as defined in
                                                R307-101-2), as applied)

Coating Category              VOC Content Limits (lb/gal)
                                 Baked          Air Dried

General, One Component            2.3             2.3
General, Multi-Component          2.3             2.8
Extreme High Gloss                3.0             2.8
Extreme Performance               3.0             3.5
Heat Resistant                    3.0             3.5
Metallic                          3.5             3.5
Pretreatment Coatings             3.5             3.5
Solar Absorbent                   3.0             3.5
                                                            

R307-346-6. Work Practices.

(1) The owner or operator shall:

(a) Store all VOC-containing coatings, thinners, and cleaning materials in closed containers;

(b) Minimize spills of VOC-containing coatings, thinners, and cleaning materials;

(c) Clean up spills immediately;

(d) Convey any coatings, thinners, and cleaning materials in closed containers or pipes;

(e) Close mixing vessels that contain VOC coatings and other materials except when specifically in use; and

(f) Minimize usage of solvents during cleaning of storage, mixing, and conveying equipment.

(2) No person shall apply any coating unless the coating application method achieves a demonstrated 65% transfer efficiency.

The following applications achieve a minimum of 65% transfer efficiency and shall be operated in accordance with the manufacturers specifications:

(a) Electrostatic application;

(b) Electrodeposition;

(c) Brush coat;

(d) Flow coat;

(e) Roll coat;

(f) Dip coat;

(g) Continuous coating;

(h) High-volume, low-pressure (HVLP) spray; or

(i) Other application method capable of achieving 65% or greater transfer efficiency, as certified by the manufacturer.

(3) Solvent cleaning operations shall be performed using cleaning materials having a VOC composite vapor pressure no greater than 1 mm Hg at 20 degrees Celsius, unless an add-on control device is used as specified in R307-346-7.

R307-346-7. Add-On Controls Systems Operations.

(1) If an add-on control system is used, the owner or operator shall install and maintain the add-on emission control system in accordance with the manufacturer recommendations and maintain 90% or greater capture and control efficiency. Determination of overall capture and control efficiency shall be determined using EPA approved methods, as follows.

(a) The capture efficiency of a VOC emission control system's VOC collection device shall be determined according to EPA's "Guidelines for Determining Capture Efficiency," January 9, 1995 and 40 CFR Part 51, Appendix M, Methods 204-204F, as applicable.

(b) The control efficiency of a VOC emission control system's VOC control device shall be determined using test methods in Appendices A-1, A-6, and A-7 to 40 CFR Part 60, for measuring flow rates, total gaseous organic concentrations, or emissions of exempt compounds, as applicable.

(c) An alternative test method may be substituted for the preceding test methods after review and approval by the EPA Administrator.

R307-346-8. Recordkeeping.

(1) The owner or operator shall maintain records of the following:

(a) Records that demonstrate compliance with R307-346. Records shall include, but are not limited to, inventory and product data sheets of all coatings and solvents subject to R307-346.

(b) If an add-on control device is used, records of key system parameters necessary to ensure compliance with R307-346-7.

(i) Key system parameters shall include, but are not limited to, temperature, pressure, flow rates, and an inspection schedule.

(ii) Key inspection parameters shall be in accordance with the manufacturer's recommendations, and as required to demonstrate operations are providing continuous emission reduction from the source during all periods that the operations cause emissions from the source.

(2) All records shall be maintained for a minimum of 2 years.

(3) Records shall be made available to the director upon request.

KEY

air pollution, emission controls, surface coating, metal furniture

Date of Enactment or Last Substantive Amendment

December 6, 2017

Notice of Continuation

March 8, 2018

Authorizing, Implemented, or Interpreted Law

19-2-104(1)(a)


Additional Information

Contact

For questions regarding the content or application of rules under Title R307, please contact the promulgating agency (Environmental Quality, Air Quality). A list of agencies with links to their homepages is available at http://www.utah.gov/government/agencylist.html or from http://www.rules.utah.gov/contact/agencycontacts.htm.